Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Driplin
List of mods: 1. HKS induction kit ( Racing Suction：DEMIO ) 2. HKS Silent High Power ( silent Hi-Power：DEMIO ) 3. Autoexe front strut bar ( Increased Body Rigidity | AutoExe Mazda Tuning & Customization ) 4. Endless MX72 Plus break pads ( ENDLESS OFFICIAL WEB SITE ) 5. K-sport street coilover ( STREET | ) 6. Camber bolts 7. Exedy stage 1 organic clutch ( MT Sports - Stage 1 Organic | EXEDY Clutch Europe ) Wheel: Mazda wheel design... Read more
By ErnieS
I have a 2023 Ioniq 6 with the original 12 VDC battery installed. It's getting long in the tooth, and I don't want to get stranded somewhere when it dies. Is it prudent with these EVs to take the car to a battery shop and have the battery tested and replaced before it fails?
By HuntedDuckV351
So now that the season is over I figured id give an overview. First off last off-season we had to tear down the 372 and found some problems that made us go up to a 4.00" crank from the 3.58". Had to have a new set of main caps installed as well as the 3 centers were loose. So we ended up going with another machinst at the start of the upgrade to the 418" and couldnt be happier with the results. So this is what the 418" has in it. First off its a 1971 340 block now with a molnar 4.00... Read more
By azaustin
Wasn’t going to post this but changed my mind after reading some recent “score” posts. Over the last couple of years I’ve thought about building an engine run stand just to “dial things in” check for things like leaks, etc. before I install an engine. Some of the kits are not bad, and I could just build one from stuff I have laying around (like the K-member on wheels I saw) but all of that takes time, and I already have more projects than I’ll live to finish. Then this run stand popped up on... Read more
By JochenWoern
My Q8 had an oil change at my Indy @58,093 miles on Oct. 15, 2026. All was good with no issues since yesterday, Nov. 07, 2026 @58,363 miles. The Mrs. took the car to a touchless carwash, and the...
By Surfer5567
1973 Plymouth duster. Runs. Drives. Stops. Body is SOLID no rust!! Its an auto, ac, power steering, disk brake car. Originally red but has been painted orange. I think with some elbow grease the original red could come back with some good patina. Has an aluminum radiator with electric fan, msd ignition. Otherwise its all stock. No leaks. I recently rebuilt the carb. It needs a new fuel tank sending unit and the wiring for the ignition switch ironed out (it works it just finicky). With those... Read more
By Oldschoolcuda
Cranking this classic after recent family probs. put a lot in perspective. Enjoy my fellow oldschooler's and retired hippies. Great seldom played song of a great music era. Oldschoolcuda http://www.youtube.com/watch?list=RD3aCfgiO_fqY&v=3aCfgiO_fqY
By cope
Looking to sell my 1966 Dodge Charger. 383 4bbl, 4 speed with Sure Grip. It’s been in storage for last 25 years. Still has Certicard and has Original Window Sticker and Invoice Receipt from 1966. Just shy of 89k miles. I’d also appreciate any recommendations of where to list it and how much it's worth. .
By cryptolime
I've been dealing with knock control spikes over the last couple months. Usually up to .65 but last week I got a spike up to .84. This always happens at light throttle, highway cruising. Always in 5th or 6th gear at lowish RPMs (below 3k). I thought it might be my A/C compressor but it does it even without using A/C. I've filled up at three different stations now so I don't think fuel quality is the issue. Any ideas on what could be causing this? I already put in fresh plugs a month... What causes knock control spikes?
By scullen27
hello! I’ve been in awe of the Lucid Air for years, but only just bought one last week through a third party dealer. I now have a 2023 Air Pure AWD in Stellar White with Mojave PurLuxe interior. There is still a year (or 10k) left on the original warranty. I already have a service appointment for this coming week to upgrade to CCCV2 and perform a maintenance and inspection. I am coming from a Volkswagen iD.4, so I am already pretty familiar with software…quirks. I haven’t spent much time... Read more
By odcics2
JoHan only made a couple to test the molds before production. I've had this in my collection for about 30 years. Asking $395. or best offer, including shipping in conus, for this rarity. Yes, there are 2 hood ornaments on the tree that would get chromed. Paypal ok. thanks for looking.
By qkcuda
I have a 4160 Holley 600 vacuum secondary carb on my 400. The part throttle response is great, but I wonder if it could use more cfm. I did some searching and it appears the 650 has the same venturi diameters but uses the larger 750 base plate (1 11/16 vs 1 9/16). Some internet searching indicates swapping the baseplates might be possible. Has anyone ever done this?
By 4mulas
Looking for a 68 roadrunner radiator for an automatic. PN. 2890945 Preferred in or near Alberta Canada so I can just pick it up in person. If you have one you don’t want let me know. Thanks
By Fran B
Magnetic Finger - Original Patented Tool for Screws & Nails The Original Magnetic Finger holds screws, nails & bolts securely in tight spots. As Seen on TV. Perfect for mechanics, craftsmen & DIY. Shop now! www.magneticfinger.com
By jagsdtc
Does anyone have experience or knowledge on how to disconnect the e-brake cable from the lever on an early A-body? I need to swap out that section of cable from the brake plate and need to disconnect the cable from the lever to remove the original one. Conversely, how do you secure the replacement cable to the lever? Thanks!
By odcics2
JoHan only made a couple to test the molds before production. I've had this in my collection for about 30 years. Asking $395. or best offer, including shipping in conus, for this rarity. Yes, there are 2 hood ornaments on the tree that would get chromed. Paypal ok. thanks for looking.
By Matt_B_5581
Hello, Wondering if someone could help me out, I'm getting ready to press in new pivot bushings, and like a dummy I forgot to take pictures of which directions they push into the axles. The only...
By snakeyes
Has any one wonder where all of our older past members are doing how many have past on or just moved on without interest in mopars ,and how blade doing hope Jiminy is staying healthy haven't heard from in a while or Marlabuck, norterndave,383moving violation, among many others ,not a poet so my writing may not be up to snuff
By Waarland
So I have a jdm rx7 fc GT-X S5 (1989), I recently took it out for its first proper drive since I imported it a year ago, I have a registration coming up and it was quite ready, one of the pulley...
By gunns54
I’ve read so many posts on this topic I’m thoroughly confused. Some of the terms used contradict the same term used in other posts and a lot of info overload. So…., For starters, I have a 2026 1500 tungsten which has the camera connector next to the left side of the license plate on the rear bumper? My understanding is that this is for an auxiliary trailer camera, which is placed on the rear of a trailer you may be pulling. 1. One of the posts states that you have to have a trailer rear... Read more
By Aforr725
My AC clutch froze up and busted my serpentine belt a few nights ago. I just moved out of state and my regular mechanic is 300 miles away. The mechanic I had it towed to is trying to brow beat me into $2300 to replace the ac system. I asked for them to install a bypass belt and he refused calling it a “modification” I know for a fact that there’s a factory provisioned option for this. I’ve already located the belt and the routing diagram and it looks like I’m going to have to do it myself in... Read more
By bigring911
Hi everyone, I’m 54 years old and have an opportunity to retrain for a new career. One direction I’m seriously considering is becoming a licensed automotive service technician, with the longer-term goal of getting into the repair, maintenance and restoration of older Japanese 4x4s, particularly Toyota Land Cruisers. I’ve always had an interest in mechanical work and older vehicles, and I’ve got a particular soft spot for the 40 Series Land Cruisers. I own an ‘81 BJ42 myself, which has... Read more
By snakeyes
thought that it might be better to have and thread for anything related to NASA and to kept it from taking up space on the aircraft thread https://www.nasa.gov/feature/goddard/nasa-goddard-technology-helps-fight-forest-pests
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
