Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Damon7826
I have 2014 Ram 1500, 180k on body, over 60k on after market Jensen Engine. There is a whining noise when I acccerate and I put it in neutral and gave it some gas and the whining continues, someone said its the bearing but I'm not driving and whining noise is heard when i give it gas in neutral is it low transmission fluid?
By MandRautomotive
Here's our 40" SLIM bar for the 2024+ F-150 with the non-modular bumper. Image: (https://mandronline.com/products/2024-ford-f150-40in-light-bar-slim) * Fits 2024-2026 F-150: XL, XLT, STX,...
By arlenroy
I have an Edlebrock electric fuel pump PO installed, the motor cranks great, no pick up issues, but it looks rigged up. I've read a few threads to place it close to the tank for suction, and not a 100% sure about the power situation. The proper hook up. Any advice would be greatly appreciated!
By Whaleman
The overall paint on my 96 is very good. The one area that is not great is my rocker panels. I don't want to try painting them myself as I am not a good spray painter. I stopped by my local small...
By Proto155
I tried searching but it pulled up too many topics not relevant to what I’ve been experiencing. So, I’ve been having an issue with my 1994 FZJ having trouble starting when it’s cold. I turn the key and the dash lights up but nothing happens. Eventually it kicks over and runs fine after that. I live in Lake Tahoe so it gets down below freezing quite often, and it seems to be getting worse. I’ve replaced the battery and the starter as well as power and ground cables in the last 6 months. Im... Read more
By ToddC
My Gravity has been in Houston for 60 days and is finally about to be shipped home. Another story. However, something interesting, I was told Lucid is about to announce a campaign for new window regulators. All 4 of mine were replaced. They have always behaved a little wonky. Apparently, about to make the announcement, but since they had the parts and my car, they went ahead and did it. Its long been speculated that they were a hardware problem. Looks like Lucid finally agrees.
By GWinger
Well really like my 2026 ram 1500 .Warranty 10year /160 k Did try to to connect one , what is Ram app on your Phone , I thought that gaves me remote start for 10 y on my phone , but Ram left that option to Subscription $13 month. That ****.. me really off 100k for truck and now you need $13 / month s….. sorry ram cheap f………… What you think ?
By TXIN
TLDR: I plan to swap an L8T and 10l80 to my 1996 FZJ80. Please follow along and provide feedback and advice as you like! I welcome any and all comments, that's how we learn. Alright guys, I've decided to start a build thread to keep myself on track with this project. I'm not the most computer savvy guy (don't use them for work anymore and I'm out of practice) so don't expect a ton of tables, fancy embedded links or the like. I will, however, do my best to share part numbers and as many... Read more
By Modular>LS
New in box, just opened to take pictures for listing. Sold the car and the T56 and still have this sitting around McLeod RXT ceramic twin disc clutch for 26 spline 8 bolt setup. Billet steel flywheel. Part # 6435807M $ 1200 $1100 shipped lower 48
By ETRADIO
My Corvette Restoration: Sometimes You’re Better Off NOT Knowing! 😂 Have you ever wondered just how much money you’ve sunk into restoring your Corvette? Or are you like me and would rather...
By McCallywood
I bought my 60 desmogged. The previous owner added a small cone filter to one of the inlet/tubes on the air intake assembly and left the other two tubes open. It’s my understanding the tube/inlet on the back is for the crank case breather hose (correct me if I’m wrong). What im trying to understand is what the other two are for, and if I should cap both or add another cone filter to the currently open one. Any insight would be appreciated.
By CWHMATT
Looking for a stock 19 ZR-1 supercharger. If you have one for sale let me know price and location. Thanks in advance!
By JustThisguy
After seeing several threads of the failures in the rear bushing of the front control arm in the 2103-16 CX-5 I did some research and saw that the 2017+ control arm appears to have a redesigned bushing to address the cracking problem. As it appears to me the cracks begin and propagate from the voids in the bushing, and the 2017+ bushing does not have any voids and appears to be thicker, so I assume it should last a bit longer at least. As I needed to replace the passenger side arm as both... Read more
By sbabbs
1990 740 factory m46, T25 car special ordered by Jim Fishers best buddie. 550 thousand miles on the original block. Never been rebuilt. A cam. 13c turbo. JohnV billet steel flywheel 240mm Saab areo 9000 pressure plate. BmW Z3 clutch disc. BMW Getrag 265 overdrive 5th trannie. Bic Longboard. Beeches! <iframe width="560" height="315" src="https://www.youtube.com/embed/5XDnAPbTkNk" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture"... Read more
By terryb
The right-hand trailer lights and the trailer brakes stopped working so I tracked down the fuses in the manual. Rear cargo area. I spent most of the time trying to figure out how to get the purple...
By Trock0311
Driver's low beam went out and I'm not getting a "lamp out" indicator on the dash. I pulled the bulb and it looked milky. Connector looked good. Replaced with an aftermarket bulb and it lights for...
By 4xdad
i noticed that i wasn’t getting any heat. coolant was right up. apparently casting sand was left in the block when mfged. so i got some system flush. i flushed the heater core both ways. seems to work fine for now. alberta in the winter is no time for a weak heater.
By sumapathi
Hi everyone, I have a 2027 C8 Z06 (non-Z07 package) with the factory tires that come with the standard Z06. I'm in Northern Virginia, and with winter approaching, I'm trying to figure out how...
By 70GS455
As further part of the dyno testing ( ...
By Vteware1
What does the long-term roadmap for DreamDrive Pro on the Air look like? What are its ultimate capabilities, and can Air owners expect features like ADB that are available on Gravity? I really would love to see ADB on the air considering the hardware is already present.
By HarryCarey64
Hello all. Am needing assistance. Bought new 2024 Ram 2500 Laramie. Have had 2 uncontrolled automatic full throttle accelerations while sitting completely stopped. First happened September 15, 2025 and pushed me into an intersection - all while I had my foot continually on the brake. Called and took immediately to dealer. They tested and said ‘it didn’t throw a code”. I said it still redlined and systematically kept pushing me. They kept for couple days and replaced the throttle... Read more
By SteveG75
OK, so as our car slowly moves through the build process, we are acquiring things like jack pucks, wheel hangers, etc. What is the opinion on wheel spacers for a GSX? We are doing the 10 spoke...
By EQCDriverUK
I am sharing my experience with a Mercedes-Benz EQC 400 4MATIC AMG Line in the UK. I would welcome factual input from other owners and technicians who have encountered similar high-voltage...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
