Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By allmoparparts67
67 Satellite Belvedere Gtx Chrome Lighter bezel. In good used condition. No pitting. $20.00 + shipping 66 67 Plymouth Dodge B body Screw kit. Missing 6 + 20 $25.00 6 Door Striker Screws. Correct with the washer. $15.00 Window crank handle alen bolts. $10.00
By rklewis1005
Ok, so next up on my rebuild list is the rear axle and diff. 70 Charger SE, 383 HP, Auto, 8 3/4 Suregrip, 489 case (not sure of gear ratio until I remove the axles and pig). It was running/driving when parked in '83 (42 years ago) and everything spins. Based on the odometer, it has around 114k miles. I'm disassembling it so I can weld new brake line brackets in place and clean/paint the axle housing. I have the workbench book (specific to Chrysler differentials) and the service manual. I... Read more
By 65AFX
Came up missing the A-pillar inside trim on both sides. I need the vertical pieces plus the T-shaped top corner. I prefer the sedan painted ones., Not the chrome ones. I have a 65 Dodge Sedan. Pretty sure 64 is the same. Attaching photo of what I have.
By Krooser
The leafs on my ‘65 are pretty sad… one is 5 leaves one is a home made 7 leaf. I have a chance to pickup a good pair of 69-70 springs cheap… I can make two springs out of four without issues but does anyone have the main leaf lengths so I know what I’m looking at?
By jimbobr
Interesting video. So are some of the replies in the comment section on YouTube. Also see Joe Tippens Protocol.
By Sedbld
For sale is a used original K&N 33-2247 engine air filter for many Ram 1500 trucks. It’s used and in good condition just needs to be cleaned. Stamped K&N 33-2247 on the edges. Asking $15 OBO plus shipping from 22630 or local pickup. PayPal, USPS MO, check or cash. Thank you FBBO!!
By Dukeboy
1967 Satellite build sheet. Anybody help with decoding?? I've looked and looked there seems plenty of fender tag decoding, but very little on actual build sheet decoding...
By 70GS455
Let's talk TQ secondary emulsion/air bleed tuning. When i first started testing my engine with a newly rebuilt TQ, the AFRs didn't quite meet the requirements. Even with changing the secondary jets, air door max open setting, etc. It was too rich in places and too lean in others - it had this weird shaped AFR curve vs rpm. So I started looking around to find out why. At WOT, the secondary air door or flap opens and forms a crude venturi, speeding up the secondary air and creating a venturi... Read more
By themechanic
I bought a new 2000 Mitsubishi Eclipse with V6 automatic and sold it after 10 years. It was a great daily driver. I drove it to Washington DC in 2003. It was a very comfortable car. I drove my oldest sister's new 1976 Ford Pinto Stallion some in Has. That was a fun driver with it's 4 cylinder 4 speed manual. But I've never owned a lightweight 2 seater convertible. I think the Mazda MX-5 looks like a fun roadster. What do/have you owned or driven?
By polywideblock
I've always had a thing for dodge street vans and b vans in general they are referred to as B vans does that make them b bodies what do you think ?
By Kowboy
Hello everyone! I am in need of some assistance on decoding a fender tag for a 64 Polara. I have owned the car since about 81. I purchased from a friends sister for $300 with the intent of pulling the motor and trans to put into a 54 F100 I had. My neighbor offered me $2000 for the car and I thought I had better look into what it was worth. I sold the truck many years back and still have the car. I drove it for many years. It has been parked for about 20 now. I recently retired and have... Read more
By tonyp25
Helping a friend who inherited a 72 Charger that hasn’t been on the road since 2023. I changed the trans filter and fluid both of which looked good with fine metal shaving in them. It shifts into reverse, drive, park, and neutral just fine. But when in drive it won’t shift to second gear. I drove it about 100 yards but when I use the slapstick to manually select 1st and then second that worked fine but no such luck in drive. After all of this I noticed the transmission linkage (I think... Read more
By Dusty997
After alot of research i noticed a trend where its damn hard to find dyno videos or write ups on a genuine poor mans motor build, almost all the ones you find involved pistons and crank work, block/head decking, or extensive port and polish work/valve jobs ext. I wanted to see what could be done on a skeleton crew budget by an average joe who doesn't have decades of knowledge or skills to lean on. So i present, the TRUE bolt ons only 440 build. To start off, a 1500$ low miles 1969 440... Read more
By MikeyM
Hi all, Hoping I can get some input on this. I've been chasing an intermittent, light, higher speed vibration that I think I've narrowed down to the front wheel bearings being a bit too loose. I jacked up the car, grabbed the wheel at 12 and 6, shook the tire and there was noticeable play; not a lot but more than enough to feel. So i followed this thread https://www.forbbodiesonly.com/moparforum/threads/how-to-properly-torque-front-wheel-bearings.126331/ and the FSM. However... Read more
By garyinmich
Is it possible to get the yellow plastic back to white? Any help appreciatef!
By mrhemi
For any ship fans out there, this is the laker Roger Blough being towed by my place on Saturday. Down bound on the St.Clair River. A bit of a bad sign, I hope it is not on the way to be scrapped. A quick Google search did not shed any light on it's current status. It had been laided up since the start of the pandemic and then suffered a catastrophic engine room fire about 18 months ago. It may have been deemed not economical to repair. The Roger Blough was the last Great Lakes freighter... Read more
By cr8crshr - Bill
So without further delay, I hope everyone having a Birthday in November HAS A GREAT ONE!!! cr8crshr-Bill
By ct71rr
Hi all, does anyone know what the correct screws used to mount the window felts to the door for a ‘71 Road Runner are? Mine were missing when I purchased my car. Screws to mount this: Are these correct?: Thanks in advance!
By SteveSS
I've mentioned our town's crazy Halloween festival, Neewollah. Halloween spelled backwards. Every year on Friday afternoon, they have the "Kiddie Parade" then the main parade on Saturday. One year my mom made my sister and me costumes to look like Brown Recluse Spiders. Problem was, we had to carry our arms at an upright angle to get the full 8-legged effect. Of course we couldn't hold our arms up that long so the effect was ruined. Mom thought we had a shot at an award but we just got... Read more
By RM23J
727 Pushbutton T-flite Reverse manual valve body Moroso deep pan 4k stall convertor Upgraded to newer front pump and tailshaft (slip yoke) Transmission has 8 passes on it. Plug and play ready! $2000 w/cables and extra cables
By RM23J
Selling the motor out of my car. This is a freshly built 440 pump gas motor .30 over bore block (76) Forged crank Keith Black 10:1 pistons Eagle rods ARP studs Built 906 heads (clean as new) Hughes solid 555/575 cam Edelbrock 2 (4) Intake (2) Edelbrock 600 crm carbs MSD distributor High volume Milodon oil pump 60 psi solid at idle 9qt. Moroso pan Making 500 and some change hp. Has been all machined with new bearings and rings, etc. More I'm forgetting I'm sure. STRONG and responsive!!! No... Read more
By 19Fury_Dude62
I've got a dumb problem. I bought a 440 recently to replace by old tired poly 318 in my '62 Fury. The engine was built by someone who passed away before he finished his car. His build didn't have power steering, but mine does. It's got an aluminum water pump housing, and crank pulley from 440Source. I purchased a reman pump, and had them put on the BB mounting bracket, and pulley. The p/s belt is out of alignment by 3/8"-1/2" There's no front to rear adjustment on the pump. Short of... Read more
By allmoparparts67
65 Belvedere or Satellite front passenger and driver side wheel lip moldings. In good used condition. Not all dented up. Mounting holes are good also. $100.00 ea.+ Shipping
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
