Stuck on "PLEASE INSERT UPDATE USB" loop
By NITO2013
Need 2013 Uconnect 8.4 ISO update file to fix loop.
Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By NITO2013
Need 2013 Uconnect 8.4 ISO update file to fix loop.

By abe
I have put together a 2027 calendar with 13 pictures of the 2026 Central PA Truckstock. If I have orders for 20 or more I can send them to you for the same amount as last year: $30 including...
By reyokonova
@SitKneelBend and I got curious one Saturday morning...... TESTED ON 2014 RAM WITH 2016 BCM: So since we had a bunch of screens and three different radio setups sitting around, we decided to do some experimenting (and risk some expensive hardware) so you guys don’t have to. We tested a mix of UC4 and UC5 radios, along with the UC4 12", UC5 12", and UC5 14.5" screens. We also tried both types of LVDS cables, and even went as far as swapping the board from a UC4 screen into a UC5... Read more
By 00thvs
Genesis just sent an email about GCS being discontinued in Canada March 1, 2027 because of Bell's 3G/HSPA network being phased out
By oslermarine
Hi all, I noticed the factory brake pads generate a lot of dust so I swapped them out for Hawk Pads. I had trouble finding the right pads so here are the correct pads Front: Hawk HB720Z.575 Brake...

By Michael Benno
Hello! does anyone have or would be willing to make a 3D scan of a S4, GT, GTS throttle body (lower intake)? It would be helpful so it can be loaded into a CAD software and some changes be modeled...
By collinn61
Is oil consumption normal on these cars? I’m at about 1700 miles from my last oil change, and I’ve lost about 3/4ths of a quart. I don’t see any visible leaks, there’s never anything on the ground, and I never even see smoke, so I’m trying to figure out where the oil is going…
By Rhino_66
Here are the ridiculous instructions for disabling the 2013 Mazda CX-5 Daytime Running Lights. This is no longer done through the diagnostic computer. Timing for the procedure is critical. If you miss a step, the procedure will fail and you will have to start over. The tech at my dealership could not get the procedure to work. The service manager and I did get it to work, but it took several tries. I think the tech was pushing the hazard switch on and off 10 times, not 5 (he was... Read more
By skates15
I have a boxster S and ordered a Carnewal exhaust and would like to know if there is a performance difference between the OEM "S" tips vs. OEM "GT" tips, or is it just appearance?
By farina43537
I removed the AW70 transmission fill tube on my car to facilitate the removal of the transmission assembly. I thought a gorilla had tightened the damn’d thing on. It took my son holding the flats on the transmission pan and me with an extended breaker bar to get it apart. Now I’m trying to figure out what’s wrong here. I’m not going to fight that thing to get it back on. Is anyone familiar with issues on these fill tubes?
By ColonelKlink
I have acquired another W212 just like the one I own. Car in good shape and sat for awhile. Both batteries OEM and were replaced previously. After sitting for many months, the main battery was...
By angrypengu
For all the reliability talk, this should be a fun thread. If you own a D5, do you regret it? For all of the good (and the bad), do you regret it? would you do it again? ...

By DRC
So, I can reach in behind wheel and kinda feel one or two nuts / clips. Do I have to remove interior kick panels to get to last one. Or can I remove the 3 screws from side moulding and hope the...
By Sanpete
Part 1 was about how (not) to apply FIPG to the water pump and related housing, according to AISIN. ...
By Daniel12
Hey guys, Looking to do a fluid swap in my t-case this week. I’ve read that guys are running Amsoil MVATF without issue. That fluid seems a bit tough to find where I am so I’m wondering if anyone has tried Valvoline MaxLife ATF in their 44-44. Got a few bottles of it on the shelf in my garage so would be great if that was a working fluid for these cases. Thanks
By Alan didit
Hello everyone, I have recently acquired a 270 stroker motor out of a 69 vette, completely rebuilt( minus the carb, which I have 2) with everything to rebuild it again, on an engine stand . It also...
By Evian
I live near Chicago. I haven' seen one early Bronco. I can't even remember seeing one in over a year. Are they numerous in your area?
By stenerson
Just bought this a couple weeks ago. I assumed it had heated sideview mirrors. Just found out it doesn't. Here in New England it's a good thing to have. Just wondering if this can be upgraded?
By angrypengu
All of the recent reliability talks about the D5 have had me thinking - and it made me realize something quite odd. I was one of the first adopters of the D5, and now, one of the last (if...

By DevinS
Selling my custom made VX performance test pipes off my C8 Z06 along with a Next-Gen OBD2 CEL delete module. These are probably one of the best made test pipes on the market for the Z06 and can no...
By Boomin
What ever it is I'd fix it and keep it. https://youtu.be/ac4wRD9c-8I?is=Ke292uI-RMfGUlZg
By hybre
In search of a C6 Corvette Radiator Air Lower Baffle Bracket - GM (15822871). TY

By Wasserkühlung
WTB any condition Image: 1999-2013 Porsche 911 convertible top rams. Part number: 997-561-945-02. These are common to fail and we rebuild many for our clients. Looking for a few pairs to...
By warrenmj
I’m just starting the process of buying and installing a Holley Sniper in my ‘66 L-79. I have a friend that has installed the Sniper in his Cobra 427 and a 240Z that he installed an LS4. He has an...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.