Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By smtyblt
Rules: If you want to sell something post up. If you want to buy something or need something post up. Post where it is for sale, how much and then once it is sold post up to tell everyone it is sold. 4/14/10 From Time to Time we will purge this thread to keep it current. If I accidentally deleted something that is still relevant let me know. - Jester
By je824016
I’m trying to find screws for my 1982 FJ60 fender vents. Does anyone know where I can find them? Thank you.
By DenverColoradoFJ60
Just rebuilt my carb, installed it and somehow it runs! hah two questions for yall to complete this long journey: Can you adjust the idle mix screw with the air intake (just the top off) while its running ? I got to the idle speed screw, just worried the vacuum wont be correct if the air intake is not sealed. I watched the video on youtube but thats an FJ40 second the high idle screw is for the choke when its fully closed right ? what rpm should this be at ? My idle is around 1k right... Read more
By excessive
Anyone know a solid / reputable / competent shop to perform an alingment on a 100 series Landcruiser in the Charleston Area? thank you.
By balmo130
Dobinsons MRR Shocks. Has anyone had these installed on their LC 200? I am starting my research, as I plan to buy a set toward the end of this year. I am looking to lift only 1.5 to 2 inches and am curious what height people went on the rear, as well as what coils they used. TIA
By Jwoodywild
Hey everyone, I wanted to post a transparent account of my experience installing the Slee Stainless Steel Brake Line Kit (Part #STF1089) on my 2003 LX 470, as well as how Slee handled the situation when brought to their attention. I run Slee rock sliders on my truck and love them, but this experience with their brake kit and customer support was disappointing. During the install, my mechanic ran into severe binding on 4 out of the 6 lines (specifically the rear female connectors). The... Read more
By kunzma
I have two sets of headliner bows for sale. $50/set plus shipping.
By dxwilson
Well, I finally bought an FJ40 after looking at them for 45+ years. I've been driving an 80 series for 20+ years, and this is a new game for me. It's a restomod done by the previous owner, and I'm going through finishing up lots of little bits to get is fully drivable. 1970, running gear is SBC 350, 700r4, and Orion transfer case. My goal is to get it ready for some Cal4wd events in the fall and winter. And I need a functioning parking brake for the safety inspections. I have the... Read more
By zalc
Just bought a (new to me) 2017 LX570 and couldn’t help but notice that the front facing camera on the screen seems to be very dark (see picture below). Is this the normal behavior of the system? It doesn’t seem to show on the top-down 360 view. Is there a way to adjust the camera settings to get a “normal” front view?
By TheBussman
New one for me. 168k miles has a noise coming from the power steering pump and low power assist complaint a little foam in the fluid. Has aftermarket pump installed. carfax says its 10 years old, heater hose was used as the reservoir to pump hose, no brand label on it but it's not painted and all the hardware looks wrong, off brand bearing can been seen with the gear off, even has aftermarket 6 sided nut holding the gear on. gear held with wooden tool in the vice for removal and install... Read more
By Zill
I purchased a 2016 land cruiser which had some nicks on the steering wheel from the previous user. It wasn't the infamous peeling problem found on the 16-17 wheels, but it appears to be some nicks from a wedding ring on the left hand. I did wrap the original wheel with a loncky steering wheel wrap, but I was not a fan of how thick it made the wheel feel. Since the steering wheel is the one item you are constantly using while driving, I thought it was worth the $750 to purchase a new wheel... Read more
By RedBean
Hey everyone, Yesterday my engine (3F-E in a '91) shut off while cruising on the interstate (scary). Check engine light was off with ignition on, meaning to power to ECU. Found EFI fuse blown. Replaced fuse and engine started and idled fine, but then fuse blew when I depressed the accelerator. Looked around and couldn't see anything wrong with the engine harness, nothing obviously broken or melted. So I called a tow to figure it out back home . Followed EFI troubleshooting in FSM and... Read more
By OM617YOTA
Alrighty, follow me on my glow plug journey. Toyota 19850-67030 - Obviously these are recommended, although expensive. Coming from 617s and $15 glow plugs, paying $70/ea had me going WTF. HKT PN, CP-22 - HKT is a Japanese brand, even OEM for some manufacturers. MUCH less expensive, so I tried them. Too good to be true, just had two fail weirdly after maybe a year, 2/4 had roughly double the ohms of new. First cold start of the day had a few misfires for a couple seconds. Not sure when the... Read more
By waynebo
Does anyone have a site where I can order a kph to mph overlay for my instrument cluster? Thank you in advance
By RadLife
Just bought my 2001 LX470, 127k miles, over the weekend knowing it had a possible transmision issue. The low mileage makes me think it's not necessarily the transmission. Here's a description of my issue. When put into R or D, the engine will rev pretty high, and then with a slight delay it will move a little bit. I tried adding ATF, and then found it leaking from the the transfer case output shaft (I only know this because I text pics and a video to a knowledgeable friend). I found this... Read more
By Theboudinking
So I am running the Slee Redarc DCDC charger system in my LC. I want to be able to connect my secondary battery to my starting battery for a "start" or "jump" assist function. I feel like the Redarc Smart start SBI 12v 200a (like what @ Eric Sarjeant did in his) is possibly to complicated for what I am trying to do. Maybe I am not seeing any other benefit that just using it other than for its "jump start" function with a switch inside the cab?!?! Or should I just run a Blue Sea Battery... Read more
By lt1fire
Putting some cheer in your lives here are the daily funny pics. I'll try to make them all as work safe as possible. ... Read more
By bull
Ladies and Gentiles, I'm currently working on a web based FJ45 registry that was started by rick_d. Orangfj45 took over where rick_d left off and I offered to help orangefj45 soon after that. I'm currently in need of your vehicle statistics so that I can fill in my list and start to debug the database. Any help from you guys would be great. If you do not want to share your info in the public forum please feel free to PM or e-mail it to me bull@toymoco.com . Please note we will not... Read more
By VADUS
A lot has been said and done regarding exhaust-side improvements for cylinder breathing in our remarkable four-valve engine. This naturally includes the twin-scroll manifold and turbocharger, which enhance wave dynamics in the divided manifold and protect the cylinders during the valve overlap phase, along with a separate exhaust path for the wastegate valves, significantly reducing backpressure behind the turbine wheel under high load. However, on the intake side, most research revolves... Read more
By Atoyot1031
The good news is that I've got a new (used) clock spring. The bad news is that I didn't need it. After my steering wheel has progressively gotten worse squeaking on left turns over the past few years, and I thought I had sprayed lube everywhere including taking apart the dash several times, I finally decided to replace the clock spring. I bought one off another mudder, and installed. Still squeaky. So, I stuck my head under the drivers footwell, with the vehicle idling so... Read more
By GTV
I've had this frame going on 10 years and yesterday I finally assembled it into a functional bike. I built it in a "traditional" klunker style with the exception of the wheels and tires. Instead of 26" Schwinn S2 wheels I'm using S4 wheels from a 50's Schwinn tandem that happen to be 650b/27.5". Front hub is from a '47 Schwinn tandem, Morrow coaster brake rear. 18x10 gearing turning a skip tooth 3/16" chain. Tires are 2.35 wide, chain stays were modified for tire clearance. Fork fits the... Read more
By eightieskid
Trying to decide between Slee or Delta rear bumper set up - any thoughts? Have Slee front bumper on order
By nabbasi
Hey folks, I’ve been around for the past year and a half or so after buying a 1967 FJ40 sight unseen and getting it roadworthy/ fun again. My first 4WD vehicle was a 100 series Land Cruiser I purchased in 2016, which subsequently became my daily driver. For older “project” or classic vehicles, I’ve got a 1968 Mustang and had a 1966 Chevy C10. Those have given/ gave me what I thought was a pretty well rounded knowledge with welding/ sheet metal, carburetors & rebuilds, brakes upgrades... Read more
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
