Sign in
Discover

News, forums and creators

Every item links back to where it was published. Follow the sources you trust to build your own front page.

Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.

Latest threads

Filters
NewestFollowing · sign in
EnglishAll languages
Any time24h7d14d30d60d90d
All publishersCorvetteForumRennlistIH8MUDFord Truck EnthusiastsFor B Bodies OnlyFor A Bodies OnlyMBWorldClubLexusRamForumAudiWorldJaguar ForumsLucid OwnersCivicXClassicBroncosTurbobricksSVTPerformanceGenesis OwnersMazdas247RX7ClubHonda-TechNorth American MotoringInsideEVs ForumEvolutionMMy350ZFT86ClubRenntech
All makesPorscheRamLexusSEATFordAudiLucidToyotaDodgeGenesisMazdaHondaPlymouthMINIJaguarVolvoMercedes-BenzBMWChryslerChevroletTeslaJeepHyundaismart
  • RamForum

    Noise: jingling, whining, crickets

    By mikeAMCS

    I just started noticing some noise that sounds like jingling, whining, or army of crickets in the last few weeks while driving. It seems like it's louder the faster I go. When in idle or park and I accelerate it doesn't seem to be as loud. Truck is a 2008 1500 hemi 5.7 with 139,303 miles that I've owned 4 years but unknown belt and pulley history so I replaced both idler bearings and drive belt. The old idler bearings seem good although they are louder than the Dorman I installed. The belt... Read more

    More Open thread at source
  • Rennlist

    mystery part 2004 911

    By UKdavo

    Getting close on my reassembly of a motor I didn't take apart. Tomorrow I will pressurize the lubrication with an analog gauge temporarily subbed in for the pressure sender. I'll take some pics of...

    More Open thread at source
  • IH8MUD

    FJ60/62 Radiator Hardware (GROMMETS / INSULATOR SPACERS)

    By ChaserFJ60

    I cannot for the life of me find anything on this little rubber grommet or the hardware used to mount the FJ60 radiator. Seemingly none of the aftermarket radiators come with any grommets or hardware. Does anyone know the part number for this little grommet? (Photo from Radiator for Land Cruiser FJ60 FJ62 - https://www.cityracerllc.com/products/radiator-for-land-cruiser-fj60-fj62 ) The other lower two are NLA looking for an alternative there as well... Read more

    More Open thread at source
  • IH8MUD

    Valve cover gasket replacement in FAQ?

    By iptman

    I search for a valve cover gasket DIY/FAQ thread but couldn't find one. Is my searchfoo not working or does one not exist? I've done the front axle service but wires and vacuum hoses scare me so I'm not looking forward to replacing this gaskets. I got a lot of oil seep from both the front and and rear of the valve cover gasket. Thanks.

    More Open thread at source
  • For A Bodies Only

    Green 1971 Dart Custom

    By Camel 111

    Hello again to everyone. I have only had my 71 Dart Custom for a couple months but have started having some great adventures, to include dealing with how Missouri works with out of state salvage titles. Took me 5 weeks to get my appointment that then required a 200 mile round trip driving in the rain. Not how I would have preferred to get to know my car but she made the trip with only one issue (water leaks) that I am in the process of addressing. While waiting for my appointment I decided... Read more

    More Open thread at source
  • Rennlist

    Battery drain

    By Ronfunk274

    I am having issues with something draining the battery. When i shut the car off there is a buzzing coming from behind the dash. I haven't been able to locate it but after ten to fifteen minutes...

    More Open thread at source
  • CorvetteForum

    Bad stumble in OD

    By zz28zz

    2000 coupe, A4, 150k miles, daily-driver, no eng mods and gets babied 99% of the time: Car was fine and had to get gas at a place I've never used before. Was OK for abt 15 miles of easy driving. Then...

    More Open thread at source
  • IH8MUD

    What did you do with your Tundra or Sequoia this weekend?

    By Bryanseye

    Couldn't find one of these threads here so I am starting one. Loaded up the family and took the Blue Ridge Parkway from Asheville to the Heintooga Ridge Road loop, then through Great Smokey Mountain National Park and into Gatlinburg. I don't think the kids know how spoiled they were traveling through this landscape. Saw a few elk which is a big deal for this southern flat lander, and got to use the CDL when I pulled off the road to let a horse trailer go by and felt the rear passenger... Read more

    More Open thread at source
  • IH8MUD

    Wilma Build

    By LLTB

    I bought this rig in August of 2024 from Erich ( @RS6tofj80 ) here on mud. He had already done quite the build on the rig (details below) and it was in pretty good shape. Erich also had all his paperwork and receipts for everything he had done to the ride. My son and I flew to Virginia to pick it up and we drove it home to Utah in two days, spending a couple of uncomfortable but memorable nights in the rig. Along the ride home we had plenty of time to notice quirks and things about... Read more

    More Open thread at source
  • Turbobricks

    micro-squirt v3 hardware manual?

    By sonofsoren

    so the megasquirt site has exceeded there bandwidth and I cannot down load the hardware manual if anyone has one they could send me I only need the part that tells you how to time a CAS adapter I bought one from yoshifab and of course the weekend I decide to get it all setup megasquirt site goes down. Hopeing someone has it saved somewhere.

    More Open thread at source
  • IH8MUD

    rear hatch no workie

    By landcruiser3DP

    when i lift the latch it doesn't feel like there is much resistance and it doesn't matter which direction i turn the lock. i think one of the latch springs let go. anyone know what the permanent solutions is, a good place to find the part or parts and if there is a temporary solution?

    More Open thread at source
  • For B Bodies Only

    426 hemi head choice, Edelbrock or Indy SR?

    By What’s up dock

    Short block is 4.2505 bore, Srp pistons, street hemi dome, so 10.5(ish) to one, racer brown 600 lift solid flat tappet. Top of cylinder already cut for larger intake valve. I’m leaning towards using a 727 with a Lupo Dynamic street strip 9.5 convertor, since I have a new one in the box, and have used that same convertor in other builds. For just a fun street engine, which head would you choose?

    More Open thread at source

Forums & communities

110 listed, 26 connected and bringing in items.

Browse all forums

Suggest a source

Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.

Sign in to suggest a source