Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Thirsty93
Wanting to know how you guys are running a mechanical temp gauge on a stock 340 intake.The sensor is only 1/8 and not very deep.I was going to use a Autometer gauge cage temp gauge but the sensor is way to big and long I thought about tapping the whole to 3/8 and going from there.Any ideas?
By UKdavo
Getting close on my reassembly of a motor I didn't take apart. Tomorrow I will pressurize the lubrication with an analog gauge temporarily subbed in for the pressure sender. I'll take some pics of...
By ChaserFJ60
I cannot for the life of me find anything on this little rubber grommet or the hardware used to mount the FJ60 radiator. Seemingly none of the aftermarket radiators come with any grommets or hardware. Does anyone know the part number for this little grommet? (Photo from Radiator for Land Cruiser FJ60 FJ62 - https://www.cityracerllc.com/products/radiator-for-land-cruiser-fj60-fj62 ) The other lower two are NLA looking for an alternative there as well... Read more
By erick993
Porsche 993 Turbo Hollow Spoke Wheels. Refinished and never installed. Part numbers 993.362.140.00 and 993.362.136.00. Includes new valve stems. Can send more pics if someone wants them. Shipping...
By leigh1322
There have been some prettty incredible claims on here by some folks that are running Mike Jones cams. Smooth idle - plenty of power - increased idle vacuum like 19" - vastly increased gas mileage...
By iptman
I search for a valve cover gasket DIY/FAQ thread but couldn't find one. Is my searchfoo not working or does one not exist? I've done the front axle service but wires and vacuum hoses scare me so I'm not looking forward to replacing this gaskets. I got a lot of oil seep from both the front and and rear of the valve cover gasket. Thanks.
By JoeBlowAudi
I’m attempting to install the illuminated front rings, part 4M8-052-112-A, on a 2026 SQ5. The middle step in the instructions below says: Connect the black cable for terminal 30 on the retrofit...
By RuskiiGuy
Looking for a Mazdaspeed Protege MAM manifold, thanks.
By bpk1959
looking for info on the performance of the 2027 z51 on the track compared to an earlier version z51 c8. im going to be switching out my 24 for 27 and im wondering how they compare on the track.
By Camel 111
Hello again to everyone. I have only had my 71 Dart Custom for a couple months but have started having some great adventures, to include dealing with how Missouri works with out of state salvage titles. Took me 5 weeks to get my appointment that then required a 200 mile round trip driving in the rain. Not how I would have preferred to get to know my car but she made the trip with only one issue (water leaks) that I am in the process of addressing. While waiting for my appointment I decided... Read more
By Eckhard
Hi, I need the trim/molding that goes above the rear finish panel on the trunk lid. Here's a picture for better understanding. The last picture shwos the part. The problem - the part needs to be shipped to germany. Best regards, Eckhard
By Ronfunk274
I am having issues with something draining the battery. When i shut the car off there is a buzzing coming from behind the dash. I haven't been able to locate it but after ten to fifteen minutes...
By Gsinbama
Is there anybody in the Alabama area that can help with replacing my sticky dashboard? I have a 2013 GS f sport that has the dreaded dashboard issue, and I’m out of the warranty timeframe
By zz28zz
2000 coupe, A4, 150k miles, daily-driver, no eng mods and gets babied 99% of the time: Car was fine and had to get gas at a place I've never used before. Was OK for abt 15 miles of easy driving. Then...
By mattmax
Recently purchased a 2015 Z06 Z07. Few bolt on mods including cold air intake, larger throttle body, Catless downpipes, X-Pipe, tuned, pulley. May be missing a few other things. No engine mods. ...
By arich
Anyone know the parts numbers for just the inserts. My local Toyota parts guys won’t get them for me
By Bryanseye
Couldn't find one of these threads here so I am starting one. Loaded up the family and took the Blue Ridge Parkway from Asheville to the Heintooga Ridge Road loop, then through Great Smokey Mountain National Park and into Gatlinburg. I don't think the kids know how spoiled they were traveling through this landscape. Saw a few elk which is a big deal for this southern flat lander, and got to use the CDL when I pulled off the road to let a horse trailer go by and felt the rear passenger... Read more
By LLTB
I bought this rig in August of 2024 from Erich ( @RS6tofj80 ) here on mud. He had already done quite the build on the rig (details below) and it was in pretty good shape. Erich also had all his paperwork and receipts for everything he had done to the ride. My son and I flew to Virginia to pick it up and we drove it home to Utah in two days, spending a couple of uncomfortable but memorable nights in the rig. Along the ride home we had plenty of time to notice quirks and things about... Read more
By spyder24
Greetings! Thanks to this forum, I was able to fix the famous leather hood rattle. The next rattle up seems to be coming from the center speaker. I have the large Infotainment screen and am not...
By chrisM916vette
Asking $239k. Only reason why I'm selling is I was offered a ZR1x at MSRP. Red Mist ext Tan interior 5500 miles Full Factory Warranty 96 month/80k mile extended warranty purchased from...
By sonofsoren
so the megasquirt site has exceeded there bandwidth and I cannot down load the hardware manual if anyone has one they could send me I only need the part that tells you how to time a CAS adapter I bought one from yoshifab and of course the weekend I decide to get it all setup megasquirt site goes down. Hopeing someone has it saved somewhere.
By landcruiser3DP
when i lift the latch it doesn't feel like there is much resistance and it doesn't matter which direction i turn the lock. i think one of the latch springs let go. anyone know what the permanent solutions is, a good place to find the part or parts and if there is a temporary solution?
By What’s up dock
Short block is 4.2505 bore, Srp pistons, street hemi dome, so 10.5(ish) to one, racer brown 600 lift solid flat tappet. Top of cylinder already cut for larger intake valve. I’m leaning towards using a 727 with a Lupo Dynamic street strip 9.5 convertor, since I have a new one in the box, and have used that same convertor in other builds. For just a fun street engine, which head would you choose?
By Ivazour
Hey all, I've just picked up a differential from the UZS186 Majesta and it has a Cusco Type RS LSD already in it, wondering if anybody has done this swap before? I've not been able to find anything...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
