Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By jltskfl
So the ignition coils and connectors are turning to dust on my daughter's 2020 C300 W205. As expected. I bought new coils, they match the factory coils. I CANNOT FIND the proper 4-pin connectors for...
By Jkoya
For the first time, our 2023 White-Silver Mini Cooper SE was able to park next to another SE. This was at Nugget Market in Sacramento, CA. At first, I though the color was black, but when I got closer it had deep blue hues in it. Nice color and it was the first time I had seen it.
By ModInJapan
Hi everyone, Mod in Japan here. We wanted to share a brake pad set for Lexus LC500 owners that we currently have on our shelf. Image: ...
By PNWnorth129
Hi everyone, I have 2016 CX-5 Touring. I attached 1 photo of each rear rotor (the one with deep scoring is right rear). Here is a timeline including more details: I got all new brake pads and rotors on all 4 wheels about 7000 miles ago. Duralast elite brake pads and Duralast rotors. Drove across the country a few months later. This past weekend I was driving up high elevation (10000ft), and going downhill for multiple minutes. I probably had my foot lightly on the brake... Read more
By propav8r
Hey y'all, on my '66 wagon I'd like to set it up with dual circuit brakes, just one line off the master to a tee for the rear drums, and a line off the front of the master to a tee for the front discs. Is the easiest/cheapest way to do this with a dual circuit later Amazon/1800 master cylinder like this? The flange on the firewall looks like there may be a bunch of stuff that fits, potentially cheaper than the... Read more
By Jaguar Forums Editor
Someone put the Type 01 SUV in an SUV body, and this rendering proves it looks more cohesive than the sedan it's based on. More......
By 68bird
Hi all, I have a 2026 SQ5 and I’m seeing two things that I think may be related. I’m curious whether anyone else with a B10 Q5/SQ5 has them. *1. Front-end shudder/chatter when turning at low...
By Coxydaimler1969
Following a master cylinder change and brake bleeding my brake/handbrake light is permanently on. If I disconnect the electrical supply to the PDWA switch will the light extinguish? (Assuming the...
By theboogers
Been looking at 26 s63. Trying to find gloss black w white interior. Not much luck. Anyhow the ones with 1k miles are around $160k. Yet new ones on the floor are not getting much discounts. Anyone...
By ModInJapan
Hello everyone, Mod in Japan here. Sharing an aero piece for Lexus RC F owners from our current stock. Image: ...
By capncarl
I have always done all of my oil changes myself for my previous cars because I assumed the people who change oil at most places are incompetent. The dealer proved me right yesterday. 2026 C43 ...
By A5Nightmare
What’s up guys I’m new here I have a 2011 Audi A5 Quattro 2.0t CAEB and I’m currently swapping it with a CPMA that came from a 2013 Audi q5 I believe? It has 59k miles. I got it off of FB marketplace...
By Rednexus
I've been posting on here for a few months now, and decided to start a build thread. Some of these will be re-posts, others will be new material. We've been a Subaru family for a long time now, which was fine when we had one kid. Once we had a second kid, and he got big enough that we could go on family camping and other outdoor trips, my wife's Outback just got too small. Last August we could barely fit everything in the Outback for a weekend of camping, even with a car top carrier. I also... Read more
By DC Tradesman
I installed a Linkswell t-style radio in my 2018 Tradesman. It has a connection for a passenger,front & rear camera. I installed those & I use them frequently for towing. I use the front camera connector for my trailer.I was wondering if anyone else has installed a Linkswell radio & found a P/N for the multi-camera interface adapter. I would like to install another camera for the driver side. I know that I could just purchase newer model & drop around 70 grand but I can’t bring myself to... Read more
By DusterDaddy415
So I was replacing my motor mounts and ended up denting the sump portion of my oil pan by accident when I jacked up the motor. It’s not terrible but it’s definitely concaved a bit. Should I be concerned?
By mudbus
Looking for intake manifold differences by part number. Anyone have a link to a trusted source? I currently have 17111-61010 and received a -6021 for replacement. Much obliged in advance
By hunterdan
Recently (5/8/26) dropped my cats and replaced them with an aftermarket set. Reasoning was two fold, wanted to replace the aging oxygen sensors as they were starting to get a bit sluggish in their reading, and wanted to swap in a set that had a better flowing y pipe. After doing the work, I could smell exhaust in the cab, but attributed it to things burning off the new pipes. Drove for the next day and 1/2 and 40 some miles just fine, but then Sunday it triggered the p219a code. Figured... Read more
By Bobzilla
Magnum alternator bracket for use with factory Magnum front engine accessory drive serpentine belt setup, without air conditioning. This is the factory bracket that places the idler pulley slightly higher away from the water pump pulley for belt clearance. This will mount to Magnum factory style cylinder heads. I am including the specific idler pulley washer and bolt, and the factory spacer used for the heater pipe spacing required when no air conditioning bracket is in that position... Read more
By CakeMountain
There's a cruiser-head in my area (Hanover, MD) that I drive by quite often. I see a 200 series, 80 series, and it looks like 3 40's under tarps. If this is you, give me a shout out. Would be glad to know who is in my neighborhood. If this super-cool individual isn't on Mud, but you know who they are, feel free to chime in. Thanks!
By Big Dad
Made a silly post about wanting a 64 and the clouds opened up .. runs, drives, stops, road ready has a bunch of new parts , needs some TLC to be sure
By FASTEDDIE1960
needing a auto transmission dipstick for my 1969 Super Bee. 383 727 automatic, non A/C car thanks much
By dkb143
I know this OptiSpark failure is a common problem, and I am suffering through a failed one now on my 1993 40th Edition, and have read MANY forum posts, but the challenge of knowing which one to buy...
By OG Style
I'm working on a 2022 A3 Quattro 2.0 and I need to replace the the crank shaft pully. I ordered a tool to hold it so I can break the bolt free and the pin spacing is wrong. I can not find the correct...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
