Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Ddaddy
Ok, this is just for giggles and grins but it got me thinking about what folks might think about the idea. A few days ago I was working on this image just for fun... After that I decided to photoshop what a '69 Dart might look like as a 4x4. What do you think...if it were a real vehicle?
By Aussie Charger
Hi guys, I have an Aussie 71 A-body. I'm looking at fitting some Corbeau seats. I assumed the floor hole dimensions would be the same as the US A-bodies (67+ Plymouth/Dodge Valiant/Dart/Demon etc). My floor holes measure 12 1/2" side-to-side and 12 1/4" front-to-back on both sides. Corbeau sent me dimensions for their A-body brackets as follows: D/S: Front Side to Side- 12 1/2" Back Side to Side- 12 1/2" Left Front to Back- 12 1/4" Right Front to Back- 12 1/4" So far, so good. But the... Read more
By lantcruiser
Hey all, first post! Have been working through a 1973 FJ40 and ran into these hubs. They were inside a tight fitting chrome cover that required lots of work just to get to the bolts. There were some odd washers as well. I have no idea how they even installed this chrome sleeve but nonetheless here’s what was underneath. Can anyone help me identify the model and what it might be from? Searching so far has not turned up anything stock on a 40. These are red because the PO painted everything... Read more
By Rich9928p
NEVER spray MAF cleaner into a hot wire MAF such as the # 0 280 214 010 used in the Porsche 928 from Euro 1984 US 1985 - 1995. It does no good as the how wire has a burn-off cycle and is...
By ChroniclerCruiser
Hey Mud, bit of a silly question. I purchased a set of Headers from Rhino Exhaust out of Australia, and they came with a set of gaskets. To my knowledge, these are aftermarket, not OEM. Is there a reason why I shouldn't use these gaskets in my install?
By dchang81
I currently have an RSQ8. Two issues I have is there's an unpredictable lag when hitting the gas unless flooring it on sport mode, and the mmi tends to take 5-10 min to connect to my phone or 10%...
By Cmartinez58
Just picked up a 996 C4s. These PSS10s were installed by a local shop in 2022 less than 5k miles ago. The spring binding is insane. Anyone ever experience this? Research is pointing me to thrust...
By Fabien92
Strange thing. My reverse lights only come on if I turn on my parking lights. I rebuilt the left tail light wiring harness, and my wiring is completely fine. I don't understand ...
By 70SwingerGuy
So Im getting ready to install the windshield in my 70 Dart 2dr. My question is about the lower gasket seating by the cowl. Obviously the other 3 sides of the gasket fit nicely over the pinch welds, but that area does not, so does the gasket kind of "seat itself" or "find its way" when the glass gets installed into it? Because there is nothing to actually lock it in place, not that I can figure out anyways. The Yucktube videos that Ive watched dont seem to address this, and the FSM is... Read more
By dnh1
I can't decide. Mine are kind of chipped up and need to be refinished. I like that mine are unique, but I also do like the HE bronze. Mine are the same wheels just were originally the black ones and powdercoated silver. At the time I got my truck in 2019 the bronze wheels were not available. I have been going back in forth on it. I have a local shop that will do all of them and mount and balance the tires for less than one bronze HE wheel costs. (PS I know... Read more
By The Full Banana
Check it out on YouTube: Volvo 242 with T5 engine swap Videos showcasing my 1980 Volvo 242 GT with a b5234t T5 engine swap, Getrag transmission, Porsche brakes, and more. www.youtube.com A brief history, linked to posts in thread: 2013 : Acquired as rolling shell; build begins 2014 : 4 cyl B230FT swap complete; epic cross-country roadtrip 2015 : Carefree driving & car shows ; 246whp dyno (full specs noted in post) ... Read more
By RezaR1
Hi All. New to the forum. I am looking for GSX convertible allocation. Please let me know if you know of one being available. Thanks
By Larmo
Does anybody have any links to web sites, that would have the wiring diagram showing the pin outs on the tipm and what they are...06 Ram 1500 5.7
By Doug
Small assortment of V12 parts: 12 EAC24I4 injector mounting cushions* 18 EAC7866 injector hose ferrule 1 EAC2863 Air Temp Sensor, * 5 EAC9761 Over run valve gasket V12 interface module for...
By C2CorvetteBob
Where is a good place to have a 1959 Corvette steering box rebuilt? Preferably somewhere in the Northwest, but anywhere would work.
By lechnoid
I just arrived in the west Phoenix, AZ from out of town. Just as I was pulling into the hotel parking lot, my '08 Z06's temperature skyrocketed from normal to 220+. Just as I pulled into a parking...
By Gold
Hello I am trying to find copies of Jim Shea's papers on 1967 late - 1968 D & R standard column papers. There is a paper # 1 and paper # 2. Last Revision 03SE2012 Also 1967 late - 1968 D & R...
By pro-streeter
Have interior code H2B B7 1969 Plymouth Road Runner. Looking for pictures of original. Service manual says Baltic blue for door and rear quarter as well as headliner trim. Photos attached for reference. wondering if this appears correct car is B5 blue
By car-fanatic
With delivery slated for next week. Getting full stealth PPF at the dealer as we speak. Here's the build sheet - how did I do? Sucks that it's just in time for winter but exciting nonetheless. I...
By Cleverparrot32
*Selling my 2019 Stingray 2LT coupe, very well taken care of. Clean title in hand. Includes 2 key fobs and all original owners manuals. Fully stock, no modifications. 53k miles. Includes desirable...
By BabyDaps
Looking for used single turbo kits everything but the ECU and wide band! Local to SOCAL and willing to travel Attached my FD that’s been sitting for 12 years
By Sneedy
I replaced the control arms and ball joint on the passenger side and the tie rods on both sides and the steering was feeling sloppy and the tire wear was uneven. I abandoned the drivers side because...
By NHRoadrunner
I need some photos and measurements from an original T bar support. This is the big t piece that holds the hood spring and has the latch bolted to it. Goes in front of the radiator support. Mine had a torch taken to it and needs a patch for the latch opening. I need photos and measurements of that triangular cut out right in front of the latch. Photo not mine. Does anyone have one handy they can take photos of?
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
