021 Ranger
By moejr
My 021 black Ranger against the red fall color of a "burning bush", won't be long before the white stuff moves in. Image:
Discover
News, forums and creators
Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
Latest threads
Filters
All publishersCorvetteForumRennlistIH8MUDFord Truck EnthusiastsFor B Bodies OnlyFor A Bodies OnlyMBWorldClubLexusRamForumAudiWorldJaguar ForumsLucid OwnersCivicXTurbobricksClassicBroncosSVTPerformanceGenesis OwnersMazdas247RX7ClubHonda-TechNorth American MotoringInsideEVs ForumEvolutionMMy350ZFT86ClubRenntech
SS Brake lines to Caliper
By yobuda
Replacing my calipers at 180K with new units from TRQ. For whatever reason, I cannot find stainless steel brake lines that go from the frame to the caliper - _for a stock height truck_. The...
Is my suspension setup properly?
By WyattK
I purchased this truck two months ago. It drives well on dirt roads and highway. However it always looks like the back end is lower than the front. It has a 2 inch spacer on the front coils and it...
Help with Blinker
By HBF
Hello, I am having problems with my blinker and wanted to see if anyone could help. My blinker went out. Replaced the flasher module about 8 months ago, that worked for a few month. (it was an LED...
Gen-Y Offset
By xr7gt390
I'm looking at a Brinkley 5th wheel that has a Gen-Y Hitch installed from the factory. Since I have a short bed F350 the dealer is recommending a Gen-Y with a 4 inch offset. Does any have...
I’ve been doing it wrong my whole life
By wyrm73
I saw this bit in an advertising email and I am left wondering how I have gone my whole life doing brake work wrong. Can someone please teach me the scoot the tire back to access the brakes...
Ford or Les Schwab for alignment?
By BPTS
2022 F350 SCCSB, 7.3 gasser-stock 20" tires & wheels. Last weekend I replaced the Hub/bearings with Axiom pieces and discovered a torn boot on the right tie rod-tie rod gets replaced Saturday so I...
240 w/ Offenhauser C-Series Intake
By TENN66
I've been researching and reading a lot and I'm wondering if the Offenhauser C-Series and a Edelbrock 500cfm carb (#1404) would be a good combination for my stock 240. I have already picked up a set...
cooling system confusion
By Bob Record
Hello, i am looking for some knowledge that i am having problems finding on the interweb, I have a 2012 F-350 6.7 powerstroke with 0 modifications, 73,800 miles and now after the engine is warmed up...
Looking for a gently used Throttle Body for F-150 5.0/5.8L
By canook2u
Anyone have a gently used throttle body for a 5.0/5.8L truck engine? I would rather not roll the dice @ the salvage yard, if possible. Please include a pic or two & asking price. . . Than you,
Ford Puck System
By 68Portagie
We use a B&W hitch in our 2016 F350. The hitch has a slight rock (LF to RR) and the locking handles will not adjust correctly.. A B&W dealer solution was to put the 5th wheel on the truck and...
'66 Wood Bed Floor
By TENN66
I finished up my wood bed floor. This truck bed isn't in the best shape, but the prior owner tried saving it and I've decided to do the same. It was a solid bed floor of 1/8" sheet metal with the...
Federal AM Radio requirements
By CyberianHusky
I recently saw news that the Federal Government was going to require car companies, to insure every car/truck has a working AM Radio. And the reason being, if anyone needed to broadcast a emergency...
truck storage!
By Listor
going to need to store the ole girl for a week or so, i want to make sure no one can drive off with her, can i just pull the starter relay to keep the alarm and the system still intact? I was reading...
2000 F150 4.6 V8 Vaccum Lines
By F150_4x4
Does anyone know the part# for each of the 4x4 vaccum lines ? Apparently these crack easy and get brittle. Mine are 5.yrs on the truck and I think they might need changing again.
Oil pan?
By voodoosurfer
My 73 has at some point had a 400M placed in it which I believe came out of a car according to the block casting number. My oil pan is a front sump style that I think they bashed in the drain plug...
NP208 fill/drain plug O-rings
By eriklane
I need the O-rings for both plugs on my NP208 transfer case. Where can I get them, or equivalent?
How uncommon is a factory Z trans code?
By 88Zbrick
Hey all! New to the forums, And new to broncos. Looking to answer a few questions about my highway legal brick! Anyways Her name is Wilma Gandy and I picked her up from the third owner about 2 months...
+1 877-365-1829 | Need Safe Wiring & Rewiring Services?
By lifehub
Hello everyone! Have you ever wondered whether the electrical wiring in your home or business is safe, reliable, and suitable for your everyday needs? Electrical wiring is one of the most...
scoping HEGO
By BillB95945
Been gleaning info from the forum for a few years. Haven't been able to find this answer: Looking for schematic for ECC4 PCB showing the HEGO input. Pins 29 & 49 1995 460 in F250
Selling a bunch of Dent and Ford related parts
By Stonebacon69399
I was going to upload each picture on here but its not letting me upload them directly from the computer and I dont have them all organized digitally. Anyhow heres a link to my facebook marketplace...
Street vs. Pro Coilovers – Are Adjustable Dampers Worth It?
By Flashark
Thought I'd share this for anyone considering a suspension refresh or looking to lower their car. Flashark has two coilover series worth comparing: Image: *Street Series* * Adjustable...
Level opinions
By Farm3r256
After purchasing my 19 F-250 I had the plans most wanted but sadly a couple months down the road it lost fuel pressure. After that non serviceable relay I ended up putting a Fass 165 and a disaster...
Forums & communities
110 listed, 26 connected and bringing in items.
Suggest a source
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.