Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Alex With a Dream
Hello everyone, I recently bought a 9th injector and EGR delete kit. I’ve been doing a lot of research on the forums about these two deletes and I understand that the 9th injector slows down start up...
By Juggs44
1 Owner, 2021 Chevrolet Corvette Stingray 2LT Z51 in Sebring Orange Tintcoat. 8,000 miles, garage kept its whole life in South Florida. Clean title, no accidents. Asking $62,000. I ordered this car...
By Souwester23
I have an '03 G500 and the front seats have been swapped with seats from a C63. I have been wanting to like these seats, but physics just isn't on my side and I'm too big to comfortably fit in them....
By bauto
as the title says looking for correct satin blade holders for a 1966 let me know what you might have thanks Bob
By 2BWise
First post! New member and wanting to post my C5 rebuild thread. I bought a 99 a little under 2 years ago. This car listed here...
By xploded
I'm trying to find Tom's TMS-17400-TUL12 exhaust. It's the stainless exhaust without the burnt tips. Anyone know where to get one, or have one for sale? Thanks
By xploded
I'm trying to find Tom's TMS-17400-TUL12 exhaust. It's the stainless exhaust without the burnt tips. Anyone know where to get one, or have one for sale? Thanks
By TimBurns
Greetings, I have gone through some old threads and wanted to see what everyone thinks. 2013 Ram 1500 154k. replaced the engine 12k miles ago after cam and lifter failure. S&J Reman with MDS Delete. It recently began missing on cylinder 5. I have replaced the coil, changed the coil with another cylinder, changed plugs and installed a brand new injector. compression test showed 175-180#. For a short time it would run after i deleted the codes but now has remained constant. does anyone have... Read more
By Birdman56
Just received email from Genesis Canada regarding Free Complimentary Ev Special Care Service . In addition to the service we are to receive a FREE NACS Adapter!
By Redtruckguy1
Hello all, I have a 95’ f150 that has a leaking heater core, the mechanic wants 800 to replace it so I was wondering if it’s something that I can do myself? I don’t have much car experience aside...
By dago64
Need guidance on this issue. In 2017 just over 100k miles my 2004 F250 was having injector concerns so sent it to the shop to repair and bullet proof since they were lifting the cab. Now truck has...
By ModInJapan
Good day everyone, Mod in Japan here. Here is an exhaust upgrade for Lexus RC200t owners that is in stock with us. Image: ...
By Ryhnoz60vette
I purchased some 1996 Dana 44 gears from a forum member a few years ago and I’m finally getting around to installing them into my 1986 Dana 44 rear end. Do I set the measurements and pinion depth to...
By BillB95945
Hi all from BillB. '95 F250 460cid 4X4 crew Been gleaning info from the forum for a few years. Haven't been able to find this answer: Looking for schematic for ECC4 PCB showing the HEGO input...
By k1500coburn
Does anyone run a Ram Aluminum Flywheel (2552) with a GM LS7 clutch? The Ram website says that flywheel works with the LS7 clutch, so that's what I installed. It wont go into gear. The clutch is...
By Lexusdriverpcb
Good evening everyone. I have the LC 500. I’m looking at painting my calipers. Everything I see on YouTube is standard calipers that are not pre-painted? It appears the LC 500 being the high-end...
By artcaley
For sale is a set of smoked front corner lights from Vette Lights. Here's a video showing them in operation just before I removed them. I went to the clear version instead....
By 3-Pedals
Is there a difference between a very early production vs a later? Were there any issues of the earlier cars? Early here means 07/17 to 09/17 and late means 12/18-03/19. Any features that changed...
By imhighlander
Howdy. My 1979 Targa has some aftermarket LED headlight inserts behind the Hella H4 lenses but I can't figure out who manufactured them. I pulled one from the vehicle but I don't see any...
By jeller68
Selling my 1976 U-100 wagon. Copper Metallic paint 1 of 787 color and trim Will need some rust repairs in the common areas. Solid chassis, rockers will need relaced. One door jam will need repaired. Vin tag in glove box, matches chassis stamp Motor runs solid, trans shifts perfect. I will freshen up the brakes, as it's been sitting a while. All in all, it's a great builder or starter bronco. Clear Nebraska title
By 2027RVLiving
I was driving my 2023 F350 yesterday and had no power at the 12 receptacle below the climate controls. Today I had power with only accessory turned on, then started, then drove at highway speed and...
By FikseGTS
I was told the ZR1X has a lithium 12 volt battery and needs a specific battery tender/charger, anyone have the part number? thanks
By LandAndStone
1977 F150 400 stock, recent rebuild by PO I am trying to track down an engine noise. It’s a tap that happens under load or acceleration only. Frequency correlates to RPM. No noise at idle. No...
By Hammer
I'm considering picking up a C6 Z06, but one of my concerns is the availability of replacement parts for the drivetrain. For those of you who own one or have experience with them, how difficult is...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
