Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By auggafj80
Looking for anyone who's had experience with a good shop in Maine that might want to tackle a head gasket job on my 08 200? 330k miles. Not really interested in going the engine swap route. My regular mechanic did the diagnosis, but he's too busy, doesn't want to tackle it.
By NedNederlander
Greetings fellow AMGers. Searched and could not find and apologies if this one is out there but hopeful for some answers or at least thoughts on this issue. Thanks in advance! The issue: Randomly,...
By PorscheKs
Rare spec with original MSRP of 213k. PTS-Brewster Green, Manual, FAL, PCCB, Burmeister and full PPF just to name a few. Original spec is with Carbon Fiber buckets and I have added custom...
By Chase991
Looking for some 991.1 Carrera S front 6 pot red brakes in good condition. Anybody have a set of these lying around after upgrading to a BBk?
By sameel
Looking for advice from anyone with UA80E experience before I decide what to do. *Car:* 2019 ES 350 (UA80E), about 155k miles. Mostly highway miles, dealer-serviced until about 112k. As far as I...
By NortheastZ06
I am located in south central MA on the MA/RI border. I have not had great luck with detailers in the past whether it be relating to ceramic coating or PPF. I am looking for a shop to do PPF and...
By handwerk
I am currently stuck in Montana trying to get home to Mn. In my 2001 LC but I had a power failure that has left me kinda stranded. Going up a hill on interstate 94 I loss power but the rigs runs ,?all gauges look good but check engine light and the 2 vac l track and off lights are on. I drove on the shoulder for almost 2 hours at 5-10 mph trying to make it to a decent sized town…, I get no reaction giving it more gas pedal no reeving or RPM increase. I finally pulled over, started it again... Read more
By SoCal818
Forgive my ignorance on this. My trailing arms bushings are cracked and moving by hand, though only slightly. At 247k miles and 21-years old, I’m confident it’s time to replace the bushings. Here’s the question - is it generally better to swap the bushings or get aftermarket replacements? They sells replacement bushing kits but I don’t know how difficult it’ll be to knock out the old ones. ( 10x Toyota Sequoia (01-07) Rear Upper/Lower/Lateral Arm Bushing Polyurethane Bushing Kit -... Read more
By WFTRAM
I have a 2003 Dodge Ram 1500 with 5.7 hemi. I am trying to find a new intake manifold without breaking the bank or getting a used one that might or might not work. I was told that Chrysler changed it and it is on a three month backorder. Any suggestions?
By Jame
4.9 i6, M5OD. Rhythmic Slapping/Bearing noise that sounds like it's from the crank/harmonic balancer. You can see I took the belt off to rule out the pulleys. There are some big clues to this. It...
By maximusbibicus
Hey folks. Last winter the drivers side door of my CX5 became very heavy and hard to open, especially when the temperatures got well below freezing. Initially I just figured that the hinge would need fresh lubricant, although I have never lubed the doors on any vehicle in 30 years and have never experienced this issue. When discussing this with a friend he mentioned the chance that the door took in water and perhaps there was/is no drainage. I did recall that for a small period the... Read more
By kennedy759
I have a 97 with 130k miles, new tires and alignment. when idling up to stop sign I can feel the car bounce up and down, at 55mph I can`t feel anything, at 65 mph on a smooth freeway I get a...
By Ron A
FYI I've been in contact with the service manager in Houston since its the only location in all of Texas. She told me they're finally opening up a service center in Dallas next month or so. That should alleviate the scheduling difficulties since they're backlogged like 3 months in advance. I finally got a service appointment in November... As far as location, I doubt its in the Legacy West location where the showroom is. There's no space, and too swanky for a repair shop Of course... Read more
By sdm100
Slightly used Carnewal Indoor Car Cover for the 2016 Boxster Spyder. It is in perfect shape and I sold the car so selling it, The Carnewal covers are polyester on the outside with a felt lining. The...
By C8Eray
2026 Oem C8 Corvette Eray cat-back Exhaust with black tips, approximately 1500 miles. It includes the oem valves/actuators Image: Image: Image: .$600Picked up only/ Los Angeles...
By ALXege
Has anyone attempted to change the size of the OE 993 Targa split rims, by mounting the center piece to a custom barrel? Have searched the internet and found nothing, although I believe technically...
By Tyler@LMR
https://lmr.com/products/promotional-new-products#29772 Have you been keeping up with what's new at LMR? Check out the link above to see what we just added. ... Read more
By Bones302
Bringing this up in hopes it can be of use to some folks on here. When I received my 13BB back in March, one of the first things I did was check for door sag and saw there was some play in the...
By Mxracer52
Selling the OEM GT4RS Weissach exhaust (OAPs + muffler + titanium tips) from my car. Swapped to aftermarket around 1,000 miles so this is like new. Located in Dallas, TX but can coordinate...
By Mxracer52
Brand new DSC Sport Controller for 718 GT4RS. Bought this for my car, forgot I had it in the midst of a relocation, and recently sold my car. It may be compatible with other models but you'll need to...
By osprey92
I've decided to take the plunge and buy a used ABS module. After watching several videos of the replacement procedure, I have a few questions: 1. Is it true that you cannot write your current VIN to a used ABS module? If true, what issues does this cause? 2. It seems a first approach might be to swap circuit boards before removing the entire module. If I only swap boards, I should NOT need to bleed the system. Correct? TIA
By mho2023
Hey folks! Made a sub $100 rotary compression tester, figured I’d post here for anyone who wants to DIY their own as well. Note this was following someone else’s guide and using their code for the...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
