Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By dmh_sr
Looking for a red exterior and red interior 67 Coupe (will consider 65 or 66 coupe) Can be NOM replacement engine and 4 speed or 5 speed Prefer complete driver quality car, but can be complete less...
By walleyejack
https://www.corvetteforum.com/forums/canadian-events/2830969-corvettes-for-sale-canadian-section-58.html post # 1157
By Dauminator63
When my 350 L48 gets up to temp, a thin, white smoke emits from the driver’s side header, cylinder #7. I recently acquired this 1977 project car, and it runs and drives but it’s essentially been...
By laserred
I'm looking at fuel pumps for my 2008 vette.base. Some pumps say they include the level sensor and some don't. What is a level sensor? And do I need to replace it also?
By walker3
Is there a way to polish your front windshield? in the sun you can see the little specks all over - not visible in the shade or when driving except when the sun is directly in front of you. is...
By DualQuadDave
Selling a nice budget topend package including 243 heads w/ Cam Motion .660 Valve Springs Ti Retainers, stock rockers w/ Summit Trunnion Kit, new 7.400 1 piece pushrods, Cometic .040 gaskets(for 6.0,...
By uapilot
Hello all. I need to replace the convertible top on my 65. Does anyone know of a shop that does good work and can install a new top for me within 200 miles of Knoxville, TN? Thank you in advance!
By TonyinKC
WTB: Nice, right side 1963 exhaust manifold part no. 3750556 with no cracks or problems. Thanks, Tony
By joeyofblades
Used for a year, no issues with it. $180 + shipping, message me your address for a shipping quote. Included in original box which will be inside the shipping box. For those who aren't familiar,...
By cheetah45
2017 Arctic White with Jet Black Z06 with CCB option(not a Z07). Trim 3LZ with new dash (2024) and ceramic tint all the way around. Paint is ceramic coated. Forgeline wheels with Michelin All...
By TMcP
_** * * $485.00 plus $15.00 U.S. shipping * * **_ Two (2) original cast-iron Power Top Deck Lid Upper Support Arms #3716395 for 1956 (no additional small hole drilled on hinge end). Removed from...
By Jatlu
Just smoked a raccoon and my front splitter was completely destroyed and my bumper split in two. Does anybody have a black c6 z06 bumper lying around and possibly the part for the underside guard as...
By dc3843
Put these on my 95 ZR1 a few months ago, but going in a different direction now. Wheels and tires have about 1000 miles on them total, no damage, perfect condition. These are the green hulk replicas....
By Hoekie
Can somebody please tell me if this is a crate motor and any info if there is any information available about it? Image:
By San Diego Ron
No need to go out and buy new ones or have the old ones [img alt="Nasty looking...
By switchlanez
Anyone have leaked literature that GM corporate distributes to their dealer salespeople? It trains them on what to say when doing competitive comparisons with other cars or within the Corvette...
By JIMNAN
Pulled the control switch for the three speeds and restored it. Functions smoothly and with very light force to operate. Cable works smoothly with minimal effort. When I attach the cable to the...
By spider2401
parts book group 2.063 leather (9/16"X15/16"). $15 shipped lower 48 bag not included. I use pay pal or zelle. PM me with any questions.
By C5Shmeli
2005 Chevrolet Corvette coupe in a rare Daytona Sunset Orange paint - first year of the C6 body style 99,961 miles. Automatic transmission. RWD. 6.0L V8 (LS2) under the hood Runs and drives...
By robwah
Looking to buy Stage 1 front splitter for my Grand Sport. GM part # 22922352
By Rapid One
I used to have this issue with my C7 years ago it would come and go and service could never find the issue until it was found to be venting of the PCV valve getting sucked in through some air intake....
By boogsawaste
My ls6 intake spit out a chunk of plastic from one of the mounting bolt locations and I’m just done with plastic intakes at this point. Looking for a bbk ssi or weiand intake if anyone has one....
By C2367
The Cold air intake was installed on Wednesday with the prototype 3D printed coupling. I well return for the new coupling in about 3 weeks.
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
