Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By ish5
Hi im new ! I have a 2016 Ram bighorn on a carli 2.5 suspension leveling kit . And running 35s on method wheels. I was wondering if anyone has ever changed the gearing on their trucks. I have the stick 3.21 from factory and unfortunately feels very sluggish and always looking for gears on the highway. Was thinking 3.92s or would 4.10s be better ?
By bedrok
My truck is haunted. 2012 F350 XLT with 6.2. It has an OCCASIONAL severe parasitic drain. It will sit for weeks just fine than in a matter of 2-3 days (as near as I can tell) it will drain the...
By raleighone
Apologies for a super long post but adding a lot here in case others have issues: I planned a camping trip leaving April 20th from NC to Portland, OR with many stops along the way before settling in Colorado for the Summer starting June 1. As you may have seen in my other posts, I did a lot of prep work with adding crossbars and a platform that holds a tent awning on one side and a shower awning on the other. I built out shelves in the back. First off, with my build, the car is incredible... Read more
By saif957
Hi All...another Porsche enthusiast...recently got a 2009 Cayenne GTS....Previously had a 2015 Macan S
By rocko
I have 2021 1500 3.6 etorque with some wiring issues related to my right rear park brake actuator. I replaced the actuator itself without testing and it turns out that wasn't the issue so that was money wasted because I couldn't return it but oh well!! It looks like a fault to ground somewhere and I'm not sure where to start. I'm basically looking for directions as to where the wiring for that particular park brake is routed under the truck? Is it one long continuous wire from the actuator... Read more
By X25
*Transmission Neutral Override Tool* I ended up having to use the tool for the first time, and it was pretty annoying. You need to remove everything in the trunk to access it, and even when you do,...
By w.Hudson
I need an Autometer mechanical oil pressure gauge. Either 2 5/8 diameter or the smaller 2 1/6 inch diameter Message me please. Anyone have an extra ? Thanks
By Snowy999
Im looking for a good used set of the above. In the UK, happy to arrange shipping!
By victoria vette 94
Hi all, ita been a while since I posted on here. I’m planning an EM long tube set up with corsa cat back. A long time ago I installed a Carroll supercharger kit and now it’s time to let it exhale....
By Ancient
Hello fellow LC enthusiasts. I have recently installed a 3.5 in lift on my LC. When driving, I feel steering wander. I also hear this noise when turning left and right. I don’t know what this is. Hopefully one of you guys can help. Video of vehicle
By Cptnslo
Need some opinions, I had a jackspania (or some rep) shifter for my kswap eg with oem cables routed thru the firewall. I installed the hybrid racing no cut kswap shifter today and used the same...
By JohnnyC
Does anybody else have any wood mods done to their cruiser? wood dash's etc? I just made a simple shelf/dash. and I had seen this other cruiser...with alot of wood mods. Alot of work went into it...here are some pics
By Wadesters
I have a restored 1980 FJ40. Engine was rebuilt 8 years ago (no smog but has catalytic converter) and probably has not had more than 2k miles since then. It is used regularly just not for long distances. Recently for good measure I replaced: wires, plugs, all filters. It runs well with lots of power but sometimes after hot it will idle really low or stall. Other times it is just fine. The times it wants to stall if I pull the choke out a slight bit to get the idle up, thus not... Read more
By Scotch
(TL;DR) - are there any shops that perform 1HD-FTE diesel "tuning" in the US? (Not quite as crazy tuning as some of our aussie friends down under, but I know there are some simple performance enhancements at the margins that could be had by someone knowledgeable in the subject and a dyno. ) Greetings from a long time listener, first time caller. My wife gives me a hard time that when I'm on an international trip I'm taking more pictures of the amazing non-us... Read more
By petegangies
Hi all, The bruiser has recently developed a whining harmonic kinda noise when lightly on the accelerator and for a second when I back off it. If I push the accelerator down harder it goes away until I go back to light throttle. Could insufficiently greased uni joints or slip joints cause this? Or am I looking at something more nefarious like a diff, transfer case or transmission issue? Car drives fine. attached sound here: Many thanks Pete
By C6007
Selling a complete LS7 performance head and cam package originally purchased for a C6 Corvette Z06 build. I paid approximately $9,800 for everything, including tax, and am asking $8,000 shipped...
By davfra
I’m having an issue with the front driver’s side brakes on my 2003 Ford F-150 SVT Lightning and could use some advice. The problem: The front driver’s side rotor becomes extremely difficult or...
By aaronzSI2017
Hello, I have recently purchased a 52670-TBG-A02, which is for the regular 10gens. This isn’t the oem part for my civic si 2017. My correct oem is 52670-TBF-A03. Can you guys tell me if the one I purchased could and would fit. I didn’t see it correctly and now I am scared I bought the wrong part. Thank you so much si people!!
By roversnomore
hey all, i know this isn't a 24v engine and i also understand that there isn't much love for the 2l-t... that being said, this one runs well, hardly smokes on cold startup. the valve train looks really tidy and unworn. this sound really seems to be coming from the head, it resonates the heatshields on the turbo... i wonder if it's a wrist pin or something in the head... maybe even an injector that is opening early?
By KiwiGreg
I tried looking for this but crashed & burned, so my apologies if this has been covered before... My 2024 LC, (two years old this week, man time flies) which I daily, rain or shine has done 11000...
By LCPilot
Please join us for the November Club meeting, 11/10/2026 at Rudy's BBQ, 30th st and route 24. 315 S 31st St, Colorado Springs, CO 80904 6 for dinner, 7 for meeting.
By stat5
What is the overall all length of the throttle cables used on 1967 GTX RT with 440 engine? Thank you for any answers.
By dimbmw
Hello. There is a technical info on how to replace the o-rings on the A/C compressor https://static.nhtsa.gov/odi/tsbs/2023/MC-10246460-0001.pdf But it does not seem to me that any human without 10...
By Antony17
Hi everyone I have a 2020 gle450 with 66,000km on it. Recently I heard rattling on the driver side rear corner. Obviously warranty is over. What are my best option to figure out what is going on?...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
