Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By dusmon
Ok Thanks in advance for the help. Looking for what parts to use to build a 904 for behind my 416. Car has 31x13 rubber 4.56 gears @ 2900# with driver Will run in the 10's. So with the knowledge here let me know what parts to get. Torque converter- Valve body- Year of 904- Clutches- Bands- Planetary- Seals-
By dodgemahal
It barely sputters but doesn't run. Do I need to pour a bunch of gas into the carb given the long runners? Yes, I have hot spark, fuel(possibly not enough), air, timing is good. Am I missing anything?
By CFD244
Hi Folks I hope this is the right place to a Magnum related question so here goes... Bone stock 1996 5.9 auto. When I start this engine it pops off immediately. Unfortunately, at times, it takes a split second for the idle to come up and sometimes stalls. When it does this, I have to put my foot to the floor to start it. Hoping to get this straightened out...Any idea where I should start looking? Thanks FABO
By appleton71
Looking for a set of front bench seat sliders for a 1974 Duster. Mine are toast.
By Radical Fred 2
Does anyone know of a company that makes a replacement skin for the rear torsion bar bracket?
By tom999w
Actually a Mopar guy I know owns it a few towns over. I found the build sheet under the seat in amazingly nice condition.
By jos51700
After pulling my motor, I was really pleased with the header gaskets that Doug's had supplied (they had really wide contact areas instead of the narrow areas on manifold gaskets), so I contacted them (via Pertronix) and asked for the part number. They have a new header gasket, called "Seal-4-Good". They were not cheap, but he said they're infinitely reusable and he's had them on and off his race car several times and reused them with no issues. Has anybody here heard of them? I'll try them... Read more
By Rocket
I have a 3.31” forged crankshaft that fits 2.500" main small block engines including 273, 318 & 340 blocks. The crankshaft has been cleaned, inspected and turned 0.010” on the mains and rod journals. This crank is drilled for manual transmissions. Rear flange has the large 1.81" register for later model torque converters starting from 1968. The crank has been sprayed with oil to prevent surface rust. This crankshaft was originally from a 273, 318 or possibly the aftermarket. It does not... Read more
By Rocket
This is a new Comp Cams solid flat tappet cam # 20-248-4 solid flat tappet cam for small block engines Specs are 0.356"/0.356" lobe lift or 0.525"/0.525" valve lift with 1.5 ratio rocker arms. Duration @ 0.050” lift is 250/250 degrees and LSA is 110 degrees. Included are the sealed instruction sheet, a packet of Comp Cams lube and the camshaft. Price for the cam is $260 shipped in the lower 48 states. I will ship elsewhere for any added cost. PM me with any questions... Read more
By Rocket
I have a new forged rotating assembly for 360 & 5.9 Magnum Mopar engines. All parts are new high-quality parts. Final cubic inches will be 408”. The assembly includes the following parts. SCAT forged 4.000” crankshaft part # 4-360-4000-6123 SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A Diamond Forged flattop 4.030” bore pistons (0.030” oversize) part # 51026 Trend wrist pins - 0.984” part # TPD-G9842750155 Diamond wrist pin locks Mahle... Read more
By moparmafia
Im looking for a pair of bucket seats for a 69 dart. Close to Ky or if you can ship to me
By Codybones
I'm looking at engine/tranny combos for my 72 Swinger and wondering what companies people have had good luck with as I see there are several out there that get good reviews. Thinking of either the 360 Magnum or 408 stroker, would like EFI but not a deal breaker if it doesn't make sense. Thanks for the input.
By WV64Signet
Seeking other owners of Windsor built A bodies. I have a 1964 Valiant Signet convertible What do you have?
By Car Nut
I’ve been receiving a lot of these coupons from O’Reillys, last month I received three, who else are getting these? $10 off $10 purchase.
By Jasper
hello all, I have new weatherstripping for the doors/trunk/hood for my 1967 Barracuda fastback. The original weatherstripping was held on by push-on clips, which were lost in a repaint by a previous owner. On a previous car I used a 3M weatherstrip cement, which held up quite well. So the question is whether I should look for replacement clips or use the #M cement? thanks!
By Kern Dog
Come on, guys...... I've seen a few members start threads and with humility, they refer to their query as a "Dumb Question". Remember the motivational speaker that said idiotic things like... There is no such thing as a stupid question ? We all know that is crap. Plenty of people ask dumb questions all the time. The members of this forum? I don't think the questions posted lately are dumb. They are just from people that have never dealt with those issues before. If a guy asks if it is... Read more
By dads65 dartgt
What do you use to attach this trim piece using these blind holes? I cannot get to the back side and they need to seal.
By timk225
My 1973 Duster 225 904 2.76 gears, runs well but the mileage is horrible,13-14, and I'm not beating on it much either. I run either 91 octane ethanol gas or 90 ethanol free. I've been through the spark timing and other settings, and things seem to be good. Biggest mods to the car are the Holley 80350 https://www.holley.com/products/fuel_systems/carburetors/street/parts/0-80350 on an iron Super Six intake, and a TTI 2-1/2" exhaust system. Today I did a vacuum test and power valve... Read more
By varlo
The car community is awesome. And I’m hoping there is maybe a member in the Lansing area that could help me out. If you are local to the area could you please pm me in regards. Thanks ! Joe
By Matt MacKinnon
Looking for the heat shield and stove intake shield for my 1972 dart swinger with a 318. Trying to find manifolds locally as shipping would be high but I am still looking for the shields and would be willing to pay for shipping. I am located on PEI in Canada. Thanks, Matt Mackinnon
By Alber
Hi All, well I took the plunge and bought my first classic car as a first project !!!!!. So I am now the proud father of a 1969 Y09 RHD Convertible Plymouth Barracuda. After checking the VIN which says the car should be Frost green and the broadcast sheet that i found in the back seat says the car was meant to be Black with blue interior ? Its been left in a garage for 15 years but the engine turns over so I was pleased... Read more
By 65 Dartman
Looking for the long manifold brace as circled used on 65/66 V8 manifolds. I will take both if need be. Shipping is to 22657
By dojo
I just found out that I probably have a 1966-1967 26 spline A833 transmission behind a 450hp 340CI, in my 1969 Barracuda. I was told this is considered to be one of the weaker transmissions. I have to get a new driveshaft made, because I went with 1350 U-joints. My question is, is it even worse remaking the driveshaft for this transmission or should I look at replacing it with a stronger transmission? Also i’m being told when you push the driveshaft into the transmission it should go further... Read more
By rslscobra
Canton LA Small Block 360 Oil Pan 7qt. with pick-up. New from Summit $375.99 and pick-up is $89.99 Both $310 pp shipped tyd. Part Number 15-910 Located in Michigan 48178
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
