1992 Early 7.3 IDI F-350 Electrical
By SS350
Truck was sitting as I acquired funds for maintenance. I replaced all fuses inside the cab. I installed reverse light LEDs. I installed new upper steering column with new multi-function switch (I had...
Discover
News, forums and creators
Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
Latest threads
Filters
All publishersCorvetteForumRennlistIH8MUDFord Truck EnthusiastsFor B Bodies OnlyFor A Bodies OnlyMBWorldClubLexusRamForumAudiWorldJaguar ForumsLucid OwnersCivicXTurbobricksClassicBroncosSVTPerformanceGenesis OwnersMazdas247RX7ClubHonda-TechNorth American MotoringInsideEVs ForumEvolutionMMy350ZFT86ClubRenntech
Front end
By johngalt56
What could be the gremlins in the front suspension? New Michelin tires, yet the truck shakes above 50 MPH . 160,000 miles on the truck
Ancillary gear... aka fridge
By powerboatr
Back 23 of sept our 2013 residential Samsung fridge compressor took a powder to avoid removing front windshield or a slide I searched again for a fridge that broke down to no more thsn 23.75 inches...
Piston camera pics
By 90project5.0
Attached are pics of my inspection camera. I know they aren’t the clearest… is what I’m seeing chunks missing/pitting on the edges? Image: Image: Image: [img alt="Is there a hair line crack...
early 04 help
By Tmbz67
*2004 early model frustration*New and need help. 04 f250 6.0 (early model) bone stock. Needing some major help. Ran the following on forscan attached in the pics. If someone can help me make sense of...
Dana 41 seals & bearings
By Grey County Hermit
I'm looking at a parts order for seals & wheel bearings for a 1950 F1 with a Dana 41 rear end, and I noticed that the catalogues all seem to refer to the Dana 44 rear end. I can't seem to determine...
1968 f250 camper
By Wmarkdale0912
Hello All: after looking for 2 yrs, just purchased 1968 f250 camper with 31K miles and minimal rust. Original owner passed away in 1984 and family parked the truck in barn. After tune up basics (360)...
Will a 89 F250 Cab fit as a swap for an 84 F-Truck?
By ghallam22
I have 2 F150’s (one might be a F100 with 150 badges), both V8 Auto’s. One is a LWB 4x4 and one’s a swb 2x4. The 2x4 cab is absolutely cooked out with rust and I want to put it back on the road, but...
What truck did you TRY to buy but couldn't?
By 49andFord
As some of you know, the wife and I (mostly it was me :D) looked for just over two years (seems longer, which is why I said "three" years earlier) to find a dump truck that would work for us in our...
2000 V10 Crank no start and gauge cluster dead
By gpjlytham
Hi All. We have a 2000 Excursion V10 2wd with approx 220,000 miles. It will crank but wont start and the gauge cluster doesn't appear to be working. Monday morning I drove to the airport and...
1973 Ranchero or Bust
By wolfcoln
Well I did find a place to put this, I added another truck to my stable. It is not your normal truck like my1953 F-600, 1964 F-250 & 1971 F-250, but it it is a fun truck nonetheless. I recently...
Auto Hold
By edjunior
Hullo all. Still learning about things in my truck. So this question is about Auto Hold. When the function engages, say when you are at a red light, do the brake lights stay on? I haven't been...
Turn Signal Wiring Harness
By Christopher2
For those who have installed your own turn signals, what did you use for the wiring? I have a couple of Signal-Stat switches to choose from and am figuring out how I want to run the wiring in...
92 E4OD Shifting Issues and 302 Blown Head Gasket
By Masczek
The transmission won't shift out of first gear until it's warmed up and I put in "Park" or "Reverse" then back into "Drive". I plan on flushing the transmission with hopes of that fixing it, anything...
2020 headlight replacement
By Wvj78
Im sure this has already been covered somewhere, but must I pull the grill and risk breaking those stupid little clips or would it be easier to try to come in from behind? It looks like the washer...
Need Help Identifying part Please
By Floridaman
Hi folks; My truck is a 97 F350 7.5l HD (ex U-haul) I'm reassembling after a lengthy repair period and have a part I can't remember where it goes. It appears to be a wiring shield? Bolts on with two...
6th gear growl
By Chainup
2017 F-350 Powerstroke with 45,000 miles used mostly for towing car hauler/camper. Starting about 5 years ago trans would make a growling sound only in 6th gear when cold. Now it does it all the time...
300/6 Manual Transmission bell housing and shift fork
By jeffreysw
I took my 1979 F-100, 300/6 manual (3-speed) to the local shop for a clutch replacement. The bell housing and shift fork are both broken. Google is telling me the standard Small Block Ford bell...
1970 F100 Ranger XLT Value
By DewittB
My dad gave me his 1970 F100 Ranger XLT (short bed, 2wd) a few years ago and we had grand plans to get it back on the road. Life has happened and with my dads grace, have decided to sell the truck. I...
Shell API CL4
By FishOnOne
Some topics worth mentioning: Looks like Ford has a preliminary rocker arm, push rod, and roller follower wear specification requirement for this new API specification. F250 and F550 trucks used...
Vacuum canister
By Ar. Hillbilly
Hey guys I haven’t been on in a while. I do have my project truck legal and on the road although it’s a long way from finished. I need to build or buy a vacuum canister for my heat /Ac controls. ...
Swapped cloth seats to leather.
By RTM
I'm about 95% finished with the leather interior swap. Head rest are going to be a problem. Image: Image: Image: Image: Image: Image:
2016 F250 Trailer Running Lights Not Working
By Tacodile
All, New member, literally just did my introduction post... I call myself searching for this particular issue and didn't find it called out, so Mods, if there's a specific answer to this, point...
1992 Bronci XLT: how to change power mirror
By HollisterBulldawg
Hello. I am looking for a video on how to remove the driver's door panel on my 1992 Bronco XLT to change the power mirror. The mirror is currently hanging by the wire. I have never taken this panel...
Forums & communities
110 listed, 26 connected and bringing in items.
Suggest a source
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.