Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By teamsideways
My son ordered the 5000-p 5.5 lift kit from duff, they're product description says it includes the parking brake cables.. they were not in the kit when it arrived at our house..$5000 including shipping.. Emailed Duff.. we're sorry those parts weren't in the kit our address is wrong and you'll have to pay 150.00 more to get them!...
By lawnmowerhombre
I had this idea and I wonder if anyone has thought of it or if it’s just a dumb idea. I wanted to recreate the ranger inner bronco door cards with zero plastic. So a thin wood for the top, proper houndstooth fabric for the lower, and find a nice billet trim for the surrounds. Is this possible? Seems like the hard part is that billet trim. Has anyone done this already? Thoughts?
By hunter1
Started removing plugs after I had replaced the cap and rotor without resolve and this is #4. What caused this carbon buildup after only about 50-60 miles on this engine? 351 RV cam with rebuilt GT-40-P heads and Fitech 400. Started having the issue week before last and then would clear back up and start again. Vacationed for a week and started it this morning and dead miss.
By joshua
Basically a Hail Mary as I really need them today as in after this nap as it’s 2 am. If you within 4 or 5 hours of me and have some good stock length shafts hit me up. Really just need the rear. But I don’t have a front shaft either.
By garciaj
I am gonna change my fuel filter which was included with my holley terminator efi kit. PN is 3033 . In the install manual it says it's a 20 micron ( this one is between the tank and pump) research recommends a 100 micron filter . I'm not sure if I should put another 20 micron filter.
This will be the official TV or Movie "Bronco Sighting" thread. If you've seen a Bronco in a TV show or movie post it here. To avoid having these kinds of threads spread out all over the forums I'll merge any other individual threads into this one, so please just post here instead and save me the time. Thanks!
By Chiclassics
Can someone point me where i can get wiper blades that fit stock 1966 wiper arms? I have the 66 wiper arms already. Heard the design changed in 68/69 and also if we get aftermarket wiper blades from WH/Toms/Dennis you also need to get matching wiper arms they wont fit stock wiper arms- is that true?.
By Smartie24
I have a flaming river steering column and an AOD transmission. I bought the lokar linkage. My transmission shift bracket is 12:00 when in park. I looking for advice on how to get the rod placemat correct so it pulls the shift lever forward on the transmission while the bracket on the steering column turns clockwise.
By DirtDonk
Just came across this on the tube of you's, and thought you all might like it. Just happens to be working on a '77 Ranger's gas door recess to fix up some rust. Nice and short, and gets the points across nicely. Enjoy. Paul
By joshua
Ok, I have a 3.5 inch lift, ax15, and the d20. My rear measurement I’m getting is 33.25 but when I have my og shaft in in can only may pull it past the yoke a 1/4 to half inch past the yoke on the axle. Seems kinda short. The front shaft it coming up 23.5 to 24 ish. I had the borgwarner shaft so I couldn’t install it with the 44 up front to verify stock length. I’m measuring from the center of where the yokes meet. Shouldn’t it be a greater distance than stock??? Also is it... Read more
By Grey owl
My question, do i need two panels?? One for constant power circuits and one for switched power circuts that only get power when key is on. The stock panel has both. The genaric Amazon fuse panel only has the constant power option. Thanks
By skrit
Not that I'm anywhere close in my build to even drive it but while I'm building... might as well make sure water stays out. Not looking for a snorkel or anything so extreme. Just don't want to spend all this time and money just to be stranded the first time I encounter manageably deep water on a trail or a rare flooded area. Explorer EFI swap with original intake plenum and modified airbox. 4r70w trans, dana 20. No lift, 33's. Thought of routing axle breather hoses high, evap... Read more
By abuffington
free... twin sticks from PO. 1972 bronco manual. wild horses brand probably 20 years old. upgraded to NV3550 and these got replaced with a new pair. JB custom boot comes with it, had to buy the fancier boot to accommodate twin sticks plus manual shifter on the tunnel. https://drive.google.com/drive/folders/1BwNnCQPKlsm085UcJQwGBc8PFw31oJDp?usp=drive_link BUFF
By JuddStack67
Looking for a good condition / usable roof rack for a 1973 Bronco. Have seen Northeast Classic Ford Parts have one listed on eBay. Condition not good enough for use without a full recondition and part replacement; that style I’ve seen in several historic pictures. But welcome any ‘period correct’ style that can be installed.
By Scoop
Thought I'd start a thread to document the mods on my 2026 4-door Stroppe Edition. I probably will not do as many mods on this one as I did on the 2022 Badlands Sasquatch - No roof rack, no heated headlights, no ditch lights, no e-steps. I already have a triple light setup to go in the Modular bumper which I have not gotten around to install yet. Also Ive ordered a Curt receiver. I'm planning on doing a hidden winch setup using the Rough Country mount and I'll install a tailgate table as... Read more
By Rombist
I was looking for some insight into which company makes a complete harness for 1975 Bronco that has a 1990 HO 5.0 Saleen EFI motor option. A lot of the harness is original to 1975 except with the 1990 mustang motor harness that I grafted to Bronco. Wanted to start planning changing it out as it will be done with paint in a month or so. It has the original C6 trans and was thinking of doing LED lights also. Thanks
By Jeff10
Hi Everyone, --- New price on 11/21/24: $47,500 --- It's been started monthly, but only driven once in the last year. Listed on Bring a Trailer last year. The build is more of a resto-mod. It's probably easiest to view all the details on BaT. Here's the link: https://bringatrailer.com/listing/1970-ford-bronco-146/ The ad that link takes you to has quite a few pictures, several videos and lots of details of the current condition. I am attaching a couple of pics to this ad for... Read more
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
