Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By '10Q7TDI_Prestige'
So the center support bearing surround on my '10 TDI's rear prop shaft/driveshaft is finally getting ready to let loose (the rubber surrounding the bearing that limits excessive movement of the...
By Sensei-bruce-wayne
Selling my aftermarket wheels and Michelin tires from my 2023 Corvette C8 Stingray Z51. Wheel Sizes: * Front: 20×9 * Rear: 21×12
By F150_4x4
Months ago I changed the lower rad hose and there was a noticable leak on installation of aftermarket rad hose and the tech made the readjustments and it stopped leaking. Today after an hour's drive...
By Skip Fix
Saw two Vettes headed west on I10 last night in Katy. one a 63/53 rag top and a 82ish blue Crossfire a few cars in front of him.
By seijack
Hello All, I was doing an oil change and checking the front suspension today and I found that the front spring adjuster bolt pads are pretty badly deteriorated on both sides with the drivers side...
By dmtfab
I am replacing the tie rod and drag link tubes on my 40 because they have rock rash and are bent. I ordered a replacement tie rod tube from CruiserTEQ, but I didn't see the convserion drag link on their new site. I could find PSDL1 - conversion drag link on the Cruiser Outfitters site though. Before I call up and order one, I was wondering if anyone knows if I can take a OEM relay rod tube and cut it to the right length and drill/tap the tube for 11/16-18 right hand... Read more
By Corvette_Nut
*Greetings Friends, I am looking to purchase a set of OEM C6 ZR1 wheels for my 2008 C6 Z06. Please let me know. Thank you for your time. Save The Wave, Corvette_Nut*
By kydave19
If one lives somewhere without any annual smog checks and doesn't plan on selling the car, how much smog crap can you remove from a 1989 240DL (5-speed manual, non-turbo) to make it run best and get best MPG?
By Real4x4
Just showing off a recent rebuild plus upgrades I did for a customer who dropped off a pile of parts in a milk crate. 6hp motor, contactor, re-zinced the brakes parts, lots more done, plus USA made Dyneema SK-78 rope (3/8 125')
By mike505
Howdy folks, I'm looking for some feedback from guys who have had Vengeance Racing tune the A8 (8L90) in their C7. I've got a 2017 Grand Sport A8 and I'm considering Vengeance for a pretty...
By Sensei-bruce-wayne
Selling my Borla ATAK exhaust from my 2023 Corvette C8 Stingray Z51. Excellent condition Image: Image: Image: . Features the NPP dual-mode exhaust system, delivering an aggressive...
By ModInJapan
Hello everyone, Mod in Japan here. Sharing a suspension upgrade for Lexus IS500 owners from our current stock. Image: ...
By tomasz
Can anybody help me finding the IAC in my car? I checked the workshop manual and the diagram that appears only shows electrical connector (not even clear where the location is from that diagram since...
By LTxDave
I started looking for a set of these and it seems they've all disappeared. Is there any at of NOS gears out there?
By Rombist
I was looking for some insight into which company makes a complete harness for 1975 Bronco that has a 1990 HO 5.0 Saleen EFI motor option. A lot of the harness is original to 1975 except with the 1990 mustang motor harness that I grafted to Bronco. Wanted to start planning changing it out as it will be done with paint in a month or so. It has the original C6 trans and was thinking of doing LED lights also. Thanks
By menzzer37
When I purchased my 2018, it had Akra headers, cats, side mufflers and rear delete section. I have a bit of drone between 65-85mph so I spoke with the guys at Soul (Paul) and he suggested I add their...
By roguescholar
No one seems to have it in stock, its 110 dollars when all others 5-10 dollars. Has anyone changed one here and trying to get around complete hose assembly which it comes with....Please I could use advice. My truck runs perfect but I would like to update 25 year old parts . Already cleaned mass air flow sensor,/ new : DPFE sensor and EGR valve sensor and last is the PCV valve....thank you in advance...appreciate your time and acumen.....neither Ford nor two auto supply stores know anything
By BGevoIX
I am looking for some stock Evo 8/9 parts for my DSM. Here is a quick rundown of what I am looking for: Evo 8/9 retainers and seats (i'll buy the springs with them, but must come with seats and...
By Check Out Bofa
Stock 2020 Civic EX Hatchback, 60k. - I replaced the original battery 3 weeks ago, got an OEM spec battery from Autozone (about $220) - Today, the car was completely dead. Busted out the multimeter - 3 volts on the battery. - Jumped the car, tested the charging current - 14.5v. So the alternator is good. - Open circuit voltage: 12.45v - Serpentine belt looks good, tension is good - Have not checked the terminals on the alternator None of the lights were left on, doors closed. Car is... New Battery --> Died 3 weeks later
By ModInJapan
Hi everyone, Mod in Japan here. We wanted to share a suspension upgrade for Lexus GS F owners that we currently have on our shelf. Image: ...
By Ming89FJ62
Not a lot of tech here. Just Chester stretching his legs
By 24RiptideBlue
Nice day here… took the Z to the grocery store… driving my Z06 is my absolute favorite way to run errands… First stop gas station, had less than an 1/8 of a tank so I was due. A young couple in a...
By SinjinC4
Trying to remove my Bose system to finally put in an aftermarket system and I can't figure out how to remove this last part? Weird looking, almost like a plus sign. Pretty small, so not easy to get...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
