Slight hesitation off idle
By jabberwoki
Only after it warms up , then some times it can buck a bit too under load. I replaced the MAP sensor but no difference. Also no codes thrown yet? 97 f150 5.4 . _____________
Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By jabberwoki
Only after it warms up , then some times it can buck a bit too under load. I replaced the MAP sensor but no difference. Also no codes thrown yet? 97 f150 5.4 . _____________
By AppalachianSurvivor
The preliminaries: My truck is a 1978 F150 Custom, 2WD, regular cab, LWB, 302 engine, 2bbl FoMoCo carb. I bought the truck in May when the weather was much cooler. Filled it up with regular...
By Dennirtime
I got a leaky freeze plug. It’s the infamous rear driver side with the dip stick and exhaust in the way. Is replacing this possible without pulling the engine or should I just throw a temporary...
By Toolmaker96
Hello all, my wife & I have a 2005 Excursion with an 05 6.0. We purchased the truck in 2021 with about 140K miles & are currently sitting at 203K. Overall it has been a great truck. For the 1st...
By Phil Humber
Hello fellas. I really need your help... I am desperately trying to get my C6 back into me 1974 F100.... I'm having a bear of a time getting the last half inch to match up and bolted... ...
By Flatlander56
Afternoon All, Working on gathering up my parts for 56 Merc build. I had a donor engine and tranny from a 1991 cube van, so I built up the 351w up to a 408 stroker engine with the C6 tranny for it....
By 49andFord
1989 Ford F-Superduty Still waiting for the LMC catalog to come in. Outside side window wipers(?) are cracked and may be allowing water to enter the doors' insides. What's a good source for...
By Bob Sacamano
Now that CAFE standards have been rolled back and the pressure to hit aggressive MPG targets is largely gone (not to mention 2027 5.0 wont have CD) Ford needs to push a simple OTA/software protocol...
By flowney
I was researching some of the older Craftsman tools I have and found this terrific reference (https://archive.org/details/SearsCraftsmanMechanicsTools1949Catalog/mode/1up). Thinking that others might...
By DentsideFan
Hey, my 1989 f-150 5.0 M5OD-R2 4x4 is having idle issues again. Alright here's the issue. When I'm driving it acts just fine zero issues with power and getting up to speed and all of that, But...
By jortucson
90 460 I'm troubleshooting why the engine shuts down when I select the front tank. The selector switch is good. Both pumps run on startup. Now I'm trying to test the fuel pressure at the EFI rail....
By liampdoyle1983
I have a 99 7.3l powerstroke diesel that when sits overnight wont start or is very hard to start the next morning but once warmed up will start no problem, replaced ICP, EBP sensors, new HPOP oil...

By PROSTOCK
It's been about 30 years since I messed with a small block, built several back then, including a clevor. It looks like I am going to do it again. Back then there were very few 302 brackets that would...
By delcatenacci
Hello there, I started having issues with my 96 powerstroke fuel gauge not reading right, it would fluctuate to over full to normal, mainly the front tank, then one day the rear tank started. I'll...
By Qwkynuf
Truck is a 2021 F350 CCLB with the 6.2 gas and 10R140. Just under 70k on the odometer. Been trying to figure out an intermittent noise. Noises are always hard to describe, but imagine putting a...
By Qwkynuf
This one really has me stumped. Back story - I recently gave my 2003 F150 to my son. I special ordered it in the fall of 2002, had to wait for it to be built, but got the exact truck I wanted (for...
By voodoosurfer
I have a 73 F250 2wd frame with a 78 400M and a C6. Dual tank bed. Does anyone have this setup with short or long tube headers? And if so what brand and part number?
By h0neydew
Having a really hard time finding the u bolts for the rear stabilizer available to purchase anywhere. Most sites only have bushings. One of mine is bent on one end. And then the part that mounts to...

By F150_4x4
5 yrs ago I replaced: * 2 vacuum solenoids * 2 soft plastic vacuum lines * Transfer case motor The 4x4 worked for 4 years. That mechanic said that one of the soft vacuum lines was leaking which...
By cokefirst
MY son and I are working on a 1956 F100 for a customer who had it to a few shops previously, but it has never been finished. One of the previous shops lost or misplaced the 4 sheet metal parts that...
By speakerfritz
looking at installing a diesel fuel system heater. its gotten interesting on whats out there. some is universal fit, some proprietary, some cheap, some expensive. before I finalize which...
By sclark900
*This 1974 Ford F-250 (F250) Camper Special Dentside spent its life in dry Central Oregon, which preserved the frame, cab mounts, rain gutters and paint. I rescued it from a farmer's field and spent...

By GN1220
I finally found a power slider a few months ago after years of looking. This morning I went to open it and discovered this. Appears that the closing cable came loose from the plastic slide the glass...
By Doc
We've owned many Expeditions. Perfect maintenance records. And each and every one had the inevitable timing chain and cam phaser problems. I'm done with the 3.5 ecoboost. They need to open their eyes...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.