Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By jcma36
Has anyone successfully installed these TRQ Front Strut & Spring Assembly Part # SCA73810 & SCA73811. I have these received these parts and notice a 7mm difference in the diameter of the new strut...
By papkade
I am doing a KC turbo swap and after putting the new turbo in and connecting the existing actuator arm it was squeaking. Curiosity got the best of me and I opened this thing up, not paying attention...
By dodge68charger
Hey Guys, Where would be the best place to get power for the electric choke on my carburetor? Im not running a ballast resistor. I heard guys tap into this. Thank you
By rtyagi2
Car: 2013 Audi Q5 2.0L (CPMA) Miles: 140000 Went to get Oil change done, put in liqui moly engine flush (running for 15 min, idle), the guy completes the engine oil change and give me my car,...
By cagotzmann
Looking at the pictures from the holley site for the 12-313 seams the float isn't in the correct location for empty. Very high above the fuel pickup level. How well does this unit read to gas...
By Sadmatt
Hi, new to site I hope this hasn't been covered. If it has please post links. I am looking for a decent bed cover for my 1987 F350 8ft I was hoping to get a Retrax Pro MX or XR but Retrax...
By Superpicky
I have the SyneticUSA MR tonneau and just recently added the roof rack, as I need to get lumber and ladder use soon. After installing the rack, the next day I'm driving and hit about 45mph when I am...
By Silver bullet 1975
Selling Milltek high flow cats with less than 3k miles on them. Putting the car back to stock to sell ASAP. They will be taken off the car next week Friday at the Chevrolet Dealership near my house...
By Briost
Greetings - I’ve had several Dodge/Ram trucks and have just purchased a 2018 Ram Tradesman with 135,000 miles. The engine is a Pentastar 3.6L with auto tranny.
By madeouttaglass
1 of 282 Daytona Sunset Orange Metallic Z's Great shape and always garaged / taken care of. The Vette Doctors of NY are responsible for most of this car. MODS: Carbon Fiber Rear Splitter...
By mysticsvt
Looking for any advice on upgrades for my 21 Shelby GT500. Currently thinking 3.8 Whipple, full exhaust, Fathouse CAI and tune. Goal is safe, 93 octane and debating on fuel system upgrades at this time. Questions I have... Cats are good to one HP? Although I think I want to remove them altogether. Engine is good to what HP? Stock Injectors are good to what HP? Fuel system upgrades to what HP? Any insight is GREATLY appreciated!
By sanchitoson
Anyone here of LP Custom Fab? Says they have a downpipe for 2019+ CX-5. Kind of pricey... 2021+ Mazda 3 2.5L Turbo 3.5” High Flow Catted Downpipe | LpCustomFAB LPCustomFab 2021+ Mazda 3 2.5L Turbo 3.5” High Flow Catted Downpipe Upgrade your Mazda 3 2021+ 2.5L turbo with our high flow 3.5-inch downpipe. Increase performance and horsepower with the GESI catalytic converter. Perfect for any car enthusiast looking for a power boost. Fit on your oem or... lpcustomfab.com Found it from here: 2021+ 2.5T Catted Downpipe - LP Custom Fab — DRTuned Racing
By just_some_guy
Howdy This will be a progress/maintenance/modification log thread for my 1993 Volvo 240 Classic. This is a car I daily, so I have no choice but to maintain it as much as possible. Limited edition maroon #1566 of 1600. Wanted an LH 2.4 car and something 1991+ for the better AC system. Would have liked a manual, but this one was too nice to pass. Will try to piece parts together for a manual swap (eventually). Car was bought sign unseen. Bought one-way plane ticket and drove it home 8... Read more
By strav
Hi All, Just joined the forum. Currently searching for my first corvette. Hoping to make that purchase soon! -Steve
By 05-E55
I recently discovered this issue exists with the 276 engines about oil wicking into the cam position sensor and magnet connectors. Has anyone experienced this? I see a pigtail connector available for...
By joserpaq
Hello All, I did my brakes and rotors all around decided to clip and tie all the sensor ends until the new wear sensors arrive. I now have a wear sensor on the dash. I went back and confirmed that...
By brianc35
The 2026 Nissan Rogue Plug-in Hybrid starts at under $46,000 with 38 miles electric range Nissan announced prices for its first plug-in hybrid (PHEV), the 2026 Rogue, will start at under $46,000. 2026 Nissan Rogue... electrek.co 38 miles of pure electric range. Sounds a lot like the Clarity in many ways. It's pricey at $46k strating price. Platinum trim pushes 50k
By unkled20
I have a crazy issue that just happened to me today. I went to drive my car to work today and it was completely dead. I tried to get in and the touchpad wouldn't open the door. When I did get in the...
By Natty C
The fuel in the tank is almost two years old. It's a new tank, installed a few years ago and has a full twenty gallons of good old 93 octane it. I want to use my drill pump to pump it out and put...
By ModInJapan
Hi everyone, Mod in Japan here. We wanted to share a rear brake pad option for IS F owners that we currently have on our shelf. Image: ...
By porscheatx
Looking for a set for an overland build im doing. Will be powder coating them so dont need a perfect set. Happy to provide shipping labels to ship them. If you have a pair laying around let me...
By dcafro
Some background: 2012 GL350, 70,000 miles. In the last month I replaced the oil cooler, turbo, a new OEM DPF, PCV, front brakes and rear suspension air bags. It’s still throwing codes: P0404,...
By Ultima Guy
I have a Launch Creader Elite 2.0. It worked well on my 2021 SR to clear any codes generated during track days. I made sure to update all the firmware/SW. It does not seem to properly...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
