Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Outsane
Joe asked me if I could help out and get this to pass smog. It also failed because of the gas cap, that has been replaced. So first I tried to set the timing, its advanced. I pulled iff the inspection plate and marked the fly wheel bb and line with a paint pen. best picture I can get. It was stuck and wouldn't rotate. I spent an hour loosening the bolts tapping the side wuth a hammer and putting a wrench on it.
By RobMc1963$
I have a set of original valve covers off a 1967 Corvette big block 427 engine. Asking $150 Image: Image: Image:
By EDoyle
Stock parts sale from low mileage late 1998 C2S. Prices are in USD. Stock gauge faces minus clock $150 Stock north American C2S springs $150 Front and rear bumperettes $100 stock...
By RobMc1963$
I have an original fan shroud off my 1966 427 big block. It has had a few repairs ( see photos). Asking $650 due to repairs. Image: Image: Image: Image: Image: Image:
By cloudshe
Anyone have experience with adding power steering to a BB (with A/C)? Recommendations? Thanks!!! bruce
By cloudshe
Anyone have experience with adding power steering to a BB (with A/C)? Recommendations? Thanks!!! bruce
By Nathan1965
I’m putting a aluminum overdrive transmission behind my 383 in my 65 Dodge coronet i’m 99% sure my crank is not drilled for a four speed I’ll add a picture for reference. How much should I have to cut off the input shaft to make it fit with the Napa bearing? I am of course gonna wait to cut it because I’m using an aftermarket bell housing from American powertrain
By spectre6000
2011 E550 4Matic. Did a bunch of work on the suspension recently. In the process of reassembly, I noticed that the holes in the factory drilled rotors has accumulated a bunch of brake dust and ate an...
By Servicetruck24
My truck is a 2024 F550. I have to change the rear brake pads myself for the first time and trying to enter maintenance mode, it doesn’t want to work. I’ve followed the instructions for this and when...
By galaysh220
Hey everyone. I’ve tried using white lithium grease all over my shifter in so many different places and I can’t resolve this squeak. It’s driving me crazy. Any ideas or anyone else experience this with the full acuity set-up? Your browser is not able to display this video.
By orangerock
I've always got new rigs every 3-4 years but with rates and prices how they are now I just can't stomach to do it again. Plus I just love this GX as it's taken me and my family all over the place and I kind of want to see how much further I can take it... It's got right around 180k miles on it right now and I've spent past 8-12 months refreshing things: alternator starter radiator pads / rotors diff fluids transmissions fluid (drain and fill) tie rods lower... Read more
By Zumo
Hello, Earlier this summer my folks downsized their living situation and my father gave me his 74 Stingray that he restored that he's had for over 20 years. I haven't done much to it but will be...
By anelson23
[img alt="this is the factory radio from the 2014"]https://cimg4.ibsrv.net/gimg/www.ford-trucks.com-vbulletin/2000x1504/img_1209_6b3e9df0223636ef988c8b92b204bbf46463abb3.jpeg[/img] this is the...
By PaxVaLoR24
Hey everyone I am trying to figure out what this noise is. I went for a drive around town, nothing crazy except maybe it got a little spirited the last mile before I got home. Sounds like it’s coming...
By just_paris
Image: Image: Image: Image: Image: Selling my C6 Z06 see mod list below. Car runs strong and is a solid everyday driver. Engine and drivetrain have about 5k miles after the rebuild. Body...
By Doing69
Does anyone know of aftermarket safty switch for clutch . (Clutch pushed in to make ground before starting)car is 1969 gtx4 speed. I’ve looked and unable to find anything . I would think it would be wired into start relay on g terminal . Thanks in advance.
By Nashou66
As the title says, has anyone used this UK based parts stamping company for Eco panels? I need a rear quarter panel , mine is rusted badly around the gas inlet door. this is the replacement...
By EDoyle
Original Porsche 993 Carrera RS script. Used, will need new glue or adhesive to fix (I like to use eurethane in a small syringe to apply). Porsche Hella kill switch 993 RS airbag delete horn...
By por944s2
Rennline Tow Hook Receiver - Billet License Plate Mount.Will ship USPO at your expense. Fits 964 to 997.2, Box & Cayman's from 99 to 12. Confirm Fitment on the Rennline website. $70 +...
By Aaron6ixBelow
1998 C5 speedometer issue — looking for some help diagnosing it I have a 1998 C5 Corvette with an automatic transmission. My speedometer stopped reading my speed. I replaced the transmission...
By Cesar@TPS
🔥 TPS C5/C6 LONG TUBE HEADERS – FREE TUNNEL PLATE SPECIAL! 🔥 *🏁 IN STOCK • READY TO SHIP • NO WAIT! 🏁* Looking to upgrade your C5 or C6 Corvette? TPS Motorsports has you covered with our *304...
By Jeff T.
Previous owner had a 6" strip installed across the top, I really don't care for it and want to remove it. I know HUD windshields are special so I don't want to screw it up removing the film. As...
By Cesar@TPS
🔥 TPS C5/C6 LONG TUBE HEADERS – FREE TUNNEL PLATE SPECIAL! 🔥 *🏁 IN STOCK • READY TO SHIP • NO WAIT! 🏁* Looking to upgrade your C5 or C6 Corvette? TPS Motorsports has you covered with our *304...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
