Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By captain_video
I'm trying to decide if it's worthwhile to try and replace the bushings on the upper and lower control arms if the ball joints are shot. I know that replacing the bushings is relatively simple with...
By firedome
1970 Duster: Anyone know what the actual rim width(s) were for stock 14" wheels? 185/70/14 in front now but would like to go 195/65/14 in front, and wider/higher in the rear if 205/75/14 will fit OK.
By Chilly
I’ve been having a problem of smoke, presumably oil coming out of my exhaust when i’m coming to a stop or sometimes starting to get moving. I’ve replaced valve cover gasket, replaced pcv, and...
By txtuffluck
2006 LC and I have a set of DT headers and XForce exhaust to install. I'm also going to be do WP/TB, pulleys, hoses, engine mounts, dif bushings, heater T's, PS lines. Also Nomad valve body, outer tie-rods and steering rack bellows, cat-back exhaust, sway bar end links, rear upper/lower control arms. I'm sure I'm forgetting some stuff too. Would pulling the engine to do all of this be worth it?
By matchek
Good morning. Car actually has a 73 - 440 engine with a new Carter carb with elec choke installed around 1985. My question 3 years ago before I had the car tuned, when the car was started, it ran strong and fast idle and then I had to pump the gas pedal for it to settle down to normal RPMs. The problem I had was stumble at acceleration. Other than replacement plugs and wires, and tune up, the main fix for that was he opened up the carb and blew it with an air hose. When I got it... Read more
By StaticTorque
I am currently pulling the RH side rear axle out to reseal everything. After taking the lock screws out of the lock ring I thought the tips looked a little different than the other side. These ones have “gone flat” or “mushroomed” the ends. Are these going to be okay to reuse? Or do I need to get new ones? I know the point is to help align everything. But I figured it being mushroomed out might make it hard. The second and third photo is after pulling the axle out, and noticed the screws... Read more
By gsbrooks
Reluctant sale — replaced by a Lotus Elise This car was a genuine contender for my forever-sports-car. It's a fantastic drive and selling it isn't easy, but the Elise arrived and the garage only...
By ROB SHARON
NEW Mallory Unilite Distributor for 413, 426, 440 Part #: 3757801 $350
By Coupman35
Today i install my glass in the door the driver side work good no trouble up and down. The passenger side goes down ok but it will not go up all the way it missing like 2 inch before it goes all the way up and it will not crank all the way up . Is there a ay to ajust that .Look like the crank will not go go no more .Any help be great thanks Also do they sell just the remote mirror small joy stick.
By volvodude
I have a 1998 Lexus ES300. The trunk leaked on the left wheel well, under spare tire and right side wheel well areas. I found that the trunk latch was very loose. After adjusting all that the...
By abrumley
So my interior fuse panel cover is shattered into pieces on my 89' FJ62, I downloaded the 60 model STL file on thingiverse #4712028 but the printed product is no where close to the OEM part, I honestly can't figure out how this is supposed to work, so, couple questions I wasn't able to answer through searching, Firstly has anyone else used the thingi print and perhaps have a picture? or Secondly, does anyone have a file to print a door like the OEM? Thanks in advance! ... Read more
By kolebyp
I have recently started restoring a 1987 Volvo 760 turbo wagon that has been sitting for almost 20 years (last registered in 2007). I refreshed the fuel system and pretty much fired right up. It had a small stumble at 4,500 rpm and I figured I would sort it out later... long story short I put tires on it, drove jt around my shop, and then it kind of became difficult to get it to fire up, which then turned into a cyl 1 miss fire. Replaced cyl 1 injector, wasnt the issue (was slightly a low... Read more
By Curtice
Any tips? I bought these channels from City Racer and seem like great quality. But almost impossible to get into the track. I was able to force them in the removable track by putting it in a vice, using a ton of lube and all my muscle power with some needle nose pushing in the channel: But for the ones that need to be installed to the permanent inner door, I cannot get the leverage to slide it in. It’s got a bunch of lube, but just stuck: I’ve been at it for a... Read more
By 69SuperBee451
I just finished the 4-speed swap in my 69. I’m running a Competition Plus shifter box, and currently have a 4078 Hurst stick. It’s obviously like shifting a truck due to the length of the shifter. The factory 5974 shifter stick is a bayonet style, and I need a two bolt style. Is there anything that is close to the height and set back of the factory 5974?
By Luftwaffel
Hello everyone, I'm new to the forum, big fan of rotary engines as a whole and found myself (in my opinion) a beautiful 1985 GSL-SE which what seems to have an interesting history. ~170k miles, it...
By jthornton
Is the snubber mount a bolt or a stud? If it's a bolt how do you back it up to take the nut off? Image: Can I just take the front loose and drop down one side and change the mounts? The...
By Takeshi
Lucid just posted a quick walk through with their software VP to Lucid Air’s UX 3.0, Enjoy all! View this content on Instagram View this content on Instagram
By POLHUSARIA
Has anyone seen this? can it be A I ? https://youtube.com/shorts/fNxTiDVrw1c?si=u0SEiLm8P_gxCJiQ
By huminajumina
After years of combing over MUD Classifieds, craigslist, marketplace, and whatever else... I finally commited to buying an FJ62. I have wanted one of these for years, and finally found the one for me. Pretty excited to get a few little things up to par, but overall its a clean cruiser and really doesn't need much work. Pretty excited to find a California cruiser with virtually no rust what so ever. Its got a freshly rebuild 3F-E and is H-55F... Read more
By GrumpyChic
Hi, Just purchased a 2023 Mazda CX-50 premium plus from carvana. This car is great, but it is missing one thing...A 360 deg camera. Can Mazda dealerships install a 360 deg camera after the fact? Thanks in advance!
By GTS2022
Found this piece on the my passenger floor mat and trying to figure out where did it come from. Image: Image:
By SteveDoten
15891952 gm right side has noted crack, both have have TEXAS road wear I have L and R what are they worth? Image: Image:
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
