Carter Carb models
By Big_Banana
Looking for a Carter 9636 for my built 318. Found a really nice 9637, but that has the Ford linkage where the 9636 is setup, linkage wise, for Chrysler. Anyone have any experience with the 9637? Thanks!
Discover
News, forums and creators
Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
Latest threads
Filters
All publishersCorvetteForumRennlistIH8MUDFord Truck EnthusiastsFor B Bodies OnlyFor A Bodies OnlyMBWorldClubLexusRamForumAudiWorldJaguar ForumsLucid OwnersCivicXTurbobricksClassicBroncosSVTPerformanceGenesis OwnersMazdas247RX7ClubHonda-TechNorth American MotoringInsideEVs ForumEvolutionMMy350ZFT86ClubRenntech
440 balance
By 1966satellite
I recently replaced the torque converter on my 440 (cast crank) engine. The one I replaced had a weight on it and the one I put in doesn't. (I know I should have known better) It now has a serious vibration. Is there any way I can balance it without removing the transmission again? I'm over 80 years old and really not able to remove the transmission again.
Gen 3 hemi swap with nag1
By chrisb67
Ok I have a 2009 challenger 5.7 with the nag trans. Putting it in a 67 satellite. Going to use sound German to control the trans. Has anyone used it. Seeing how the wiring is tied in. I know about the 8hp but I have this whole car so don’t want to have to get a different transmission, shifter and tcm. So any info or ideas. Thanks
Steering box
By moparjwp1966
I. Have a 1966 Cornett I need a new steering box I am upgrading the front suspension including disc brakes I have had mixed reviews on the Lares steering boxes I am looking at the 10-1 box any experience with Lares boxes would be helpful. Thanks
Finally, first time at the track
By Virg464
Finally got to take the car to the track for T&T, Mid Mich Motorplex. Been a long time coming, what a great feeling! Got to make 4 passes, let up each run a little farther down the track, wanted to make sure things were going to stay together, last pass was a full run. Best time 12.339, best MPH 106.38, first time for me too so my RT's were horrible, best was .321 (lot of work to do there) Now I know she goes, so paint job will be next. If I can figure out how to post a... Read more
NOS Urethane Road Wheel 1975-1977 #3699487
By marty mopar
There is a small amount of surface rust on the outer edge of the wheel. This will be covered by the trim ring. 85.00 plus shipping 480-966-6683 www.ar izonaparts.com Have lots of other Mirada, Cordoba, Magnum etc. B Body parts 1975-83
Want a functioning day/night rear view mirror for my 65 Coronet.
By 493 Mike
I recently broke off the switch lever on my OEM mirror. I only need the actual mirror, not the mount. This is my daily driver not a restoration. Mike
64 Plymouth Splash Shield
By matthon
Looking for driver's side front inner fender splash shield, covers the headlights. Below is a pic of my rusted shield, as well as the rust free shield in another car.
66-67 Charger quarter window trim fasteners?
By Speedbird
The problem is the length or "throat". They are the speed nuts, clip nuts, j-nuts, tinnerman nuts, spring clips, etc. etc, etc. The originals used like a number 6 flat head screws to be flush with the stainless trim there. I've been looking on line for a while now. All short stuff. I could use some thing else like fender washers and plain nuts with machine screws. But it is sort of hard to get too. Any sources? ... Read more
1969 GTX P6G Dark Green Interior Plastic Paint Comparison
By braydun
Hello, Members. I have spent the last two months trying to find a paint that closely matches the original P6G Dark Green Metallic molded-plastic interior pieces in my 1969 GTX. My reference is an original, well-preserved A-pillar trim piece. I compared each sample directly against it in different angles and lighting conditions. The attached photos show my original A-pillar material behind each painted sample. Paints Compared OER — #434 Dark Green Metallic... Read more
RB vs B Dizzy Shaft Length and Rocker Shaft Bolts
By Krooser
Two questions B vs RB dizzy shaft length? Also which bolts go where when assembling an RB rocker shaft? Also I would like to see if I have the rockers on the correct orientation. I have a service manual but I can’t get it out of the trunk right now!
Big Block/hemi Super Stock aluminum water pump housing
By Outlaw525
Mopar aluminum water pump housing #2205862. Nice condition. This it what they put on the early Super Stock engines. $230 shipped CONUS I can do Paypal, F&F or add $15 for fees. Message if interested. Thanks
Disc brake conversion
By CaptainAtom
Hey everyone, I'm doing a rear disc brake conversion on my '67 Charger and need some help because I'm not familiar with this stuff at all. https://www.jegs.com/i/JEGS/555/631...oc4C6BEdTjpKjMxSMLkWfSSvqomt9lmcaAtAiEALw_wcB ... Read more
Bouchillion 727 Kickdown Cable Kit. PROBLEM!
By 62maxx
The cable will NOT allow me to attach the snap connector to the ball stud on the 727 kickdown lever and then try to fasten it to the supplied/installed cable bracket. It's jus way too short! I tried adjusting the (CARB) end with the push button but NOPE! Of course it's the weekend and they are closed. ANYBODY have a solution or similar problem? I think they gave me the wrong cable..... THANKS!
New Guy from SoCal
By SoCal Mikt
Hi There - I live in SoCal and am thinking of buying a 1968 Road Runner. Many years ago I had a 1970 Challenger with the 440 engine in Plum Crazy purple, white side stripe, white interior and white vinyl top. Loved that car but long gone. I plan on posting a listing I saw soon on a 1968 Road Runner to see what you guys think of it. Look forward to finding out more about theses cars. Mike
T bars
By old guys rule
Looking for advice on T bars for early B bodies for handling or for ride OR for a possible combination of both with RB/manual box.
Body Shop Recommendations Near Atlanta?
By yagami
Looking for a company or person reputable and willing to replace the floor boards on a 60s b body. Every company and person I've spoken to gives some form of "you need to find someone that knows someone". Any recommendations of ideally a business that would do a good job with this?
Good guy alert Dartn440
By davek
Doug @Dartn440 lives in NC I bought the front plate holder/1 year only and bottom back seat for the 70 Charger. He basically gave them to me. Doug has TONS of A body parts if anyone needs something also some B body parts Thanks Doug and it was nice to meet another brother from the site.
Best Rock & Roll Riffs
By Pops1967GTX
We all love Music & are cars. What are your favorite Riffs of Music... Theses are my Top all time... Thunderstruck -AC/DC Sweet Home Alabama - Lynyrd Skynyrd Layla - Derek And The Dominos Oh Pretty Woman - Roy Orbison Frankenstein - Edgar Winter Jessica-Allman Brothers Band http://www.youtube.com/watch?v=rHQqMS-2gHM&feature=related http://www.youtube.com/watch?v=xiC__IjCa2s
New 1970 bucket seat belt set blue
By moparsaver
Pretty sure they are 70, please correct me as needed Looks like we ordered 2 sets and didn’t realize it so offering this set for sale. Brand new complete set just opened the bags to get pics. There is a set of front shoulder harness mounting covers included and a generic set of instructions. Asking $425 shipping included in the USA, International for additional shipping cost. Thanks FBBO. ... Read more
440 4 Barrel decals
By allmoparparts67
440 4 Barrel decals. $30.00 Plymouth Barracuda decal. $20.00 Dodge Boys decal $30.00 Richard Petty Decals $20.00 ea.
Forums & communities
110 listed, 26 connected and bringing in items.
Suggest a source
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.