Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By l6hmus
Hello, I have a 69 Valiant and I have noticed that my rear spring travel is limited by the shock travel. The shock bottoms out before I get to the pump stops. What are you using to get more travel from the shocks (so far I have used regular RockAuto shocks)
By littleredcoffin
This is a brand New hardware kit to secure the headlight rings.$9.Keene NH.US Postal money order only
By maldridgeks
Hello everyone, I’m looking at a 73 charger that had a Jasper 340 installed over 20 years ago. Any experience or insights you can share as to the quality and performance I might expect? Thank you.
By AbodyBB
I am searching for my 71 duster that was stolen from my land in Rosamond CA. It was stored in my trailer which I believe was the real target of the theft. If anything shows up that is that green or you think it may be it’s a V8 car with power brakes big bolt conversion on the front and B body 8 3/4 in the rear. Last numbers of the VIN 133362
By firedome
The steel wheels on my all original Gold Duster are 14" 5 bolt x 4" hole-spread (measured straight across center to center). A local guy has some A-body rally he says came off a disc-brake '74 A-Body, bolt hole spacing of 4.25"? What are the varieties of 14" rally wheels and which will work with stock hubs? Are there adapters to make other sizes work, (iirc B-bodies used 4.5" bolt-hole spacing rally wheels?).
By firedome
There's a '76 Volare V8 parts car with discs/power brakes, it has 4.5 wheels. Besides the hubs and calipers and m/c-booster, what would be needed to do a disc brake conversion on my '70 /6 Duster with 4 wheel drums? All wheels, hubs, calipers and drums are on the parts car still.
By mopowers
Is there a way to wire a relay so that a circuit is turned on and off with a "normally open" momentary switch? If so, can you point me to a wiring diagram? If not, does anyone make a special latching relay to make this happen?
By VAD Gold Rush
I’ve been having some problems for the entirety of my car being together. The cheaper radiator I used has never kept up, and I’m looking to finally make a change to a good radiator. What 22” radiators are y'all using for your big block cars? Mine has the standard driver side outlet water pump. Pic is just for fun, so y’all can enjoy my work in progress next to my girlfriend’s Valiant.
By 1WildRT
Build Thread for my 68 Coronet R/T Convertible
By easymopar56
Hi I'm having trouble finding a pigtail wiring for my front turn signal bec turn signal blink nine but parking light doesn't work . I've tried classic industries,Jegs, summit racing , Mopar mega parts and year one (year one only have lens and housing but not available yet ) eBay doesn't have clean or good one for drivers side
By gerahead
Has anyone used Q-bond to repair/recreate the little ridge on the molded fiberglass heater box half where the little metal clips are attached? I am restoring a box that is perfect, except for a couple of locations where the small metal clips attach has been blown out. I found a brief reference to a product called Q-bond that was used to repair this feature, but didn't include any process details. Has anyone here used this Q-bond adhesive to make this repair and is willing to share how they... Read more
By Dodge68charger
I’d like to take some load off the Ammeter in my 1970 Duster. I Dont wanna disconnect it. Would running a 4 gauge wire with a fusible link from the battery to the starter relay help with that?
By 340sport
Used A-body fuel sender 5/16" No gasket, lock ring or sock/filter $30 shipped to your door in U.S. Located in Western MD
By littleredcoffin
These are in Excellent condition.1-10,Solid 8.5-9s.Com e with the mounting nuts!!$15pr.Keene NH.US Postal money order only
By dojo
I recently changed the ring and pinion in my 1969 Barracuda 8 3/4 rear end. And now I’m trying to put it back together, but the locking nuts are very old and I can’t find them anywhere besides eBay. I went to local parts store and picked up some 3/4 by 24 locking nuts, but I would rather use factory if I could. What is everybody using to tighten up their carrier?
By 68 bee
I have a pair of 1970-71 Dart Swinger headlight bezels for sale. They are in good condition with no cracks that I can see. One has a small chip. I’m asking $50 for the pair plus shipping from Huntington NY 11746. Message me if you’re interested ... Read more
By DatMoparGuy
Like new metal filler (splash) panels. $100 for the pair. Located in Tecumseh OK.can ship for cost.
By 70SwingerGuy
So I installed brand new roof rail weatherstrip in my 70 Swinger, and it looks noticeably different than what came out of it. It fits in the stainless channel just fine, and seems to only install one way without simply falling out. The front A pillar section seems ok, but from there back is where it really looks different. The seals are from Metro Molded Parts, and their stuff is usually pretty good, but it just seems like this is the wrong seal. Ive verified that its the proper part#... Read more
By Lee Robinson
I have a pair of front frame rails and a TB crossmember from a 65 Valiant. I think the rails will fit 60-73 A bodies and the TB crossmember will fit 63-66. The 67 up cars are wider and take a different TB crossmember. $250.00 each piece from a Ca. car plus shipping from El Dorado Hills, Ca. PM me if interested.
By Thirsty93
Need a new steering box for my 69 swinger with manual steering.Which one should I buy and do I need a different steering ratio Would like to use stock pitman arm
By Blue62Val
Hi guys, Just chasing an air cleaner base to suit a 65 Barracuda 273 Commando, Carter 4bbl for my Formula S. I think it has a 4 1/4” hole ? I just need the base if someone has a spare. Thanks. Peter
By M_Body_Coupe
The 9800 series (the 'Aftermarket' series w/ the attached electric choke) has been my carb of choice for a number of years. I've done a bunch of tuning with this thing, many lessons learned, etc. More specifically, given the combo I'm running (408, W2, Comp Cams XR292HR cam but on 112 LSA, Victor 2920 single plane intake, 4K stall converter and 4.10 gearing) I had taken the approach of drilling the primary butterflies to provide the engine some bypass air, otherwise the primaries needed to... Read more
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
