Super Clean V8 fender badges.$15pr
By littleredcoffin
These are in Excellent condition.1-10,Solid 8.5-9s.Com e with the mounting nuts!!$15pr.Keene NH.US Postal money order only
Discover
News, forums and creators
Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
Latest threads
Filters
All publishersCorvetteForumRennlistIH8MUDFord Truck EnthusiastsFor B Bodies OnlyFor A Bodies OnlyMBWorldClubLexusRamForumAudiWorldJaguar ForumsLucid OwnersCivicXClassicBroncosTurbobricksSVTPerformanceGenesis OwnersMazdas247RX7ClubNorth American MotoringHonda-TechInsideEVs ForumEvolutionMMy350ZFT86ClubRenntech
Torque converter swap
By Daniel Brunner
One year later than planned, but this winter it’s time to upgrade my converter. Because some stuff needs to be de-bolted anyways I‘ll change some seals too of course. I appreciate any tips or advices for installation/seal replacement 904 TF Thank you
Mercedes W221 Steering Wheel
By Ntrepid
I am helping my dad (a lifelong Mercedes customer) clear out some of the parts he has collected over the years. This is one of 3 steering wheels he has which I am listing. The part number I could...
8 3/4 locking hardware
By dojo
I recently changed the ring and pinion in my 1969 Barracuda 8 3/4 rear end. And now I’m trying to put it back together, but the locking nuts are very old and I can’t find them anywhere besides eBay. I went to local parts store and picked up some 3/4 by 24 locking nuts, but I would rather use factory if I could. What is everybody using to tighten up their carrier?
05 RX330 P0430 Diagnosis, Looking for sanity check
By 91cruiser
I’m trying to diagnose a recurring P0430 on our 2005 RX330 (3MZ-FE), currently at about 152k miles, and I’d appreciate some input before I go any further. The code first appeared around 140,859...
Replaced rear level sensors, new baseline height?
By CRab
I’ve recently replaced my level sensors and now I’m sitting on the bump stops. I can put the suspension on High and it will rise and stay there overnight, so I know I don’t have a leak. I have a Launch device and I’m able to go into test mode and raise it and drive around, however as soon as I reset by turning it off and back on the “normal” height goes back to sitting on the bumps. I’ve tried putting it on jacks at the higher level, clearing all codes, doing the reset zero in the VSC... Read more
New VBOX HD1 - Anyone used one yet?
By snotdocz
Definitely a little more accessible than the higher-end VBOX systems. Was looking into an HD2, but this looks pretty cool. https://www.vboxmotorsport.co.uk/us/vbox-video-hd1-camera ...
Frustrations with BMulator
By cpalm
Hi All! This is my first post here and unfortunately it has to be about a problem i’m needing some insight on. Just gonna give some context but if you wanna skip to the problem go down. I have a 1997...
2023 Camaro based 70 Chevelle Conversion
By themechanic
We saw a beautiful red one last weekend at a local car show. Nicely done, too. Looks factory. The owner trailored it from Dallas. It's making the show circuit but he said he plans to drive it after that. Trans Am Worldwide Debuts Camaro Based, 70/SS Retromod Chevelle
Mercedes-Benz ML (W163) and S-Class (W220) Steering Wheel
By Ntrepid
I am helping my dad (a lifelong Mercedes customer) clear out some of the parts he has collected over the years. This is one of 3 steering wheels he has which I am listing. The part number...
What to name her?
By 49andFord
Two people have now asked, "what will you name her?" One suggested "Bertha." I'm not sure I like that, but I've found myself calling her that at least once. So, suggestions? What name does she...
Injector wiring harness help
By aridaen
Hi, I'm chasing a misfire and high idle issue on my 86.5. So far I've smoke tested everything with no issues and ensured there are no vacuum leaks. I had an issue with cylinder 5 spark so I replaced...
1970-71 Dart headlight bezels
By 68 bee
I have a pair of 1970-71 Dart Swinger headlight bezels for sale. They are in good condition with no cracks that I can see. One has a small chip. I’m asking $50 for the pair plus shipping from Huntington NY 11746. Message me if you’re interested ... Read more
C2 grille brackets
By Lund1952
Looking for instructions on how to crimp the rivets for the brackets on 65 vette. Want them tight so grille is solid or should I use bolts, nuts and washers? Thanks
1970 GTX
By willy wagon
just checking to see if anyone has recently purchased a 22 inch rad for their car. mine is a 22 inch in a 1970 Plymouth GTX. need to replace it with the same but want it to look very stock
Duster Front Inner Fender Filler Panel (metal)
By DatMoparGuy
Like new metal filler (splash) panels. $100 for the pair. Located in Tecumseh OK.can ship for cost.
Recent lease rates on 2026 GLC 300
By kingofire
This is my first time ever leasing any vehicle. So I wanted to know what people are recently paying and discounts. The 2026 GLC I'm looking at is MSRPd at $62xxx. They're giving me $8000 off....
Cross ram velocity stacks
By Outlaw525
Set of cross ram velocity stacks. These are the angled, staggered height ones. I was told that they came from Ray Barton. $175 shipped in CONUS. Can do Paypal F&F or add $10 for fees. Message if interested. Thanks
New Member
By jones1090
New to the Porsche world after browsing for a few years. Trying to get some posts in to allow for PMs to be sent at some point. If anyone has some front red 997.2 GT3 calipers they want to...
FS (For Sale) 2014 Blade silver 3LT SC M7
By Boostedfi
For Sale: 2014 Chevrolet Corvette 3LT Coupe (7-Speed Manual)Price: $49,500Mileage: 2,700 Original MilesExterior: Blade Silver MetallicInterior: Adrenaline RedTransmission: 7-Speed Manual (M7)Title:...
Good machine shops in the Dallas/Fort Worth area
By mizzleman
Hello! It's time to do the rear brakes on my truck. Rotors are thick so I'd like to have them turned. Anyone know of a good machine shop in the DFW area that can turn rotors for a decent price?...
Forums & communities
110 listed, 26 connected and bringing in items.
Suggest a source
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.