Sign in
Discover

News, forums and creators

Every item links back to where it was published. Follow the sources you trust to build your own front page.

Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.

Latest threads

  • For B Bodies Only

    Torque converter hub size

    By Gunner1

    Hi guys The 440 block and crank in my car came out of a 76 motor home. It’s a cast external balance but the flex plate is the one cut so no weight is needed. Or so they say. Anyway mines balanced zero rear. I think I’m going to need a new converter soon. The car won’t brake torque above 2500 anymore. In fact it creeps pretty hard at 750 hot idle and is sluggish off the line. If I tell them what my crank is will they know what I need ou do I need to pull it and measure. Recommend a good shop... Read more

  • For B Bodies Only

    1964 Fury Bucket Seat Tracks

    By 66/440

    I want (need) to refurbish the bucket seat tracks for my '64 Fury. I have seen several threads on the later model tracks but nothing for earlier seats. Has anyone done this? I need to understand how to separate the tracks so I can inspect / blast / paint and lube. All help appreciated as usual pictures are the gold standard! Thanks

  • ClubLexus

    2015 Lexus Gx460

    By mojeko

    hellooo... anybody know what part number on ignition coil connector housing...? i planning to change my spark plug... and i heard that push tub it always break... thank you and God Bless

  • For A Bodies Only

    CC volume intake ports

    By MazdaRX8/6

    I decided to CC the intake ports of a1986 head vs an older peanut plug head. The ports on the newer head measure larger in the intake opening, but surprising to me, the port volume measured the same. 80-95 cc. Does that surprise anyone but me?

  • ClubLexus

    AJT's Escalade V

    By AJT123

    Folks, I'm about 95% sure it's a go tomorrow! We've been discussing for a few hours. There are no cons. Worst case scenerio, sell it and take a couple thousand bucks loss. Needs some floor...

  • For B Bodies Only

    Advice for first-time in-car torque converter drain

    By Coelacanth

    I just replaced my transmission filter and pan gasket after emptying the transmission fluid. The job was a lot less messy by first pumping out most of the fluid from the dipstick tube with a hand pump; almost no tranny fluid was spilled. That's a good tip for others planning to do the same job. I want to replace the tranny fluid that's in the original torque converter, I've never done that before. Apparently I can remove the inspection cover on my 1970 Charger's 727 bell... Read more

  • RamForum

    Have a 4th Gen jump seat - looking for Full Console swap

    By Case45

    I'm looking for someone that wants to swap their 4th Gen Ram pickup full console for my partial console/ jump seat assembly from a 2015 Ram 2500 Laramie. My console/jump seat is black and in excellent condition. This swap requires swapping the radio bezel and lower dash trim pieces as well. Your console MUST be: - In good/great condition - Black in Color, both the body and the lid. - include all mounting brackets, HVAC ducting, and trim pieces. - be from a 2013-2018 Ram Your radio bezel... Read more

  • IH8MUD

    FJ40 Exhaust Kit

    By 72Roper

    Does anyone have a recommendation for a a vendor or resource that sells a full exhaust system as a kit? I found a couple threads on here that referenced a vendors kit but it had been discontinued when I looked it up (can’t remember the vendor offhand) Any feedback appreciated!

  • Rennlist

    Part number help

    By xmaciek82x

    While changing my oil the other day, I noticed one of the rubber seals is looking very odd. Red arrow in the below picture. I'm unsure if it was installed incorrectly by someone or if it is...

  • For B Bodies Only

    oil pressure

    By 73rrrd

    I have a 73 roadrunner with a 340 , I decided to put in a mechanical oil pressure gauge, after I got it in I drove it around drove great was showing around 50 psi on initial start up after driving and warming up around 25 - 30 psi just driving around, as I'm about a block from home my pressure gauge was showing 0 , was running great pulled it into the garage and shut it off . so I decided to pull the coil wire take out the oil sending unit from the block to see if oil would shoot out of the... Read more

  • For B Bodies Only

    I'm done buffing!!

    By t.flatt

    After putting this job off for a few years it was time to get it done. And, thank God it is!!! It's a big job to take on and I already know sanding bores the hell out of me! The orange peel wasn't that bad so I started with 1500 grit, then 2000, 2500, 3000 on a DA, then 3M's 3 step process of pads and polishes. I think it came out pretty damn good!

  • CivicX

    (Built Motor, FBO, Hondata Fuel System) 2017 Aegean Blue Honda Civic Type R 40K Minnesota

    By AWildDugong

    Up for sale is my 2017 Aegean Blue Honda Civic Type R, just under 21,000 miles. Clean Carfax, 2nd owner bought with 26 miles on the odometer. Always garaged and stored for the winter. All parts have been professionally installed by Impulse Performance in Minnesota. This car is track and show ready! Will throw in a set of Volk TE37 Saga S-Plus Matte Black 18 x 9.5 +38 wrapped in like new Nankang CRS (2022 compound, <100 miles on them) 265/35/18 for 51k. Performance/Engine - 4 Piston short... (Built Motor, FBO, Hondata Fuel System) 2017 Aegean Blue Honda Civic Type R 40K Minnesota

Forums & communities

110 listed, 26 connected and bringing in items.

Browse all forums

Suggest a source

Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.

Sign in to suggest a source