Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By GM87
Hi everyone, I’m looking for a Ford Intercooler hose OEM DR3Z-8D029-A for my 2013 Shelby GT500. I’m interested in either: -)New / NOS, or -)Used, as long as it is complete, undamaged and unmodified. If anyone has one available, or knows someone parting out a 2013–2014 Shelby GT500 who might have it, please send me a PM. Part number: DR3Z-8D029-A, number 6 in the picture below Thanks!
By Boogie Chillin
I took a shot at cleaning up the center console cup holder / ash tray. I designed a few press fit covers. I'm not a fan of chrome but I didn't want anything too flat or cause any damage. The center console looks finished now instead of empty and keeping it functional. The red in the photo is a little off with the flash. It matches the SVT red logo / tach pretty well.
By SRBCitrusCobra17
This is not a new issue, but I have been curious about the source of the noise. I hear a clunk from underneath the car when I back it out of the garage, sometimes hear it when I turn a corner, and when I switch from forward to reverse. It is hard to tell whether it is from the front or the rear. This has existed for years, before and after engine removal where the K was dropped. My thought was in the suspension areas. I have looked at IRS mounts, front suspension etc. Nothing obvious... Read more
By Merlin
2025 Lexus RX 350 CQUARTZ Finest Reserve Ceramic Coating A Miracle Detailing Inspection: DeFelsko PosiTest DFT Paint Thickness Gauge for ferrous/non-ferrous metals DeFelsko 200C3-G PosiTector 200 C3 Advanced Ultrasonic Coating Thickness Gauge Lighting: ScanGrip MultiMatch 8 and MultiMatch 3 color from 2500k to 6500k. ScanGrip Sunmatch 3 Machines: RUPES Bigfoot iBrid Nano Long Neck RUPES BigFoot HLR 75E Mini Rupes LHR 21 with... Read more
By cobra_4
Pigeon Forge Rod Run Fall 2026 Rod run time again! Make sure you check back for more Rod Run video's or visit our archives for a couple decades of Rod Run coverage!#rodrun #pigeonforge #p... youtu.be
By projectslideways
Looking for ideas for a quick connect battery tender setup (no hood pop). Battery is in the factory location. Anyone have any good ideas/examples?
By Recon
Watch Out Power Stroke & Cummins: The 8.3L Duramax V8 Diesel Is Coming to Eat Your Lunch! ( https://www.allTFL.com ) Check out our new spot to find ALL our TFLstudios content, from news to videos and our podcasts! Watch Out Power Stroke & Cummins:... youtu.be Shows details of the engine and chassis specs. Dubbed the mongoose, 555hp and 1230ft lbs of torque. Forged internals. Sent from somewhere in the twilight zone…
By BULLITT 4940
Probably a shot in the dark but it a try i have 2000 cobra r 101 I’m looking for the black binder . I have had the car since 2015 called ford and the first owner no luck I got the car from fisher imports in California no longer open l would pay what it is worth if located and it is real . Any help would be greatly appreciated.
By IFlyEm81
I purchased the car in 2017 with 33,000 miles and 100% stock. All of the modifications were done by me and the car has been meticulously cared for. The Procharger was installed on 5/2023 at 47,140 miles. It has never seen the track under my ownership and has been out pretty much just for local car shows. I did have it dyno'd when tuning for the Procharger, and it put down 572 RWHP and 462 RWTQ on a Mustang Dyno at Throttle Works. Ortiz Performance says there is definitely more power... Read more
By AZ SVT
Please post pics of your SVT Focus here. We all want to see them and it takes too long to drive to everyone's house Also, we encourage you to add your SVTF to the SVT Registry (click for SVT Registry) Effective February 20, 2003, If you include your build number, your first name, and the state you live in when you post in this thread, that will be taken as a request to be added to the registry. You can also PM Versey Vic here: (click to PM Versey Vic) if you have... Read more
By 03Cobraman$
Does anyone know where to get OEM lower ball joints (F4-ZZ-3050-A/AA? Looking for lower ball joint boots also - I prefer rubber.
By oster910
First and foremost I will clear this up, the car was purchased with 18,000 miles The car was a "flood car" I went this route because I didn't want to get a car with any kind of frame damage and based on the research I figured it would be good to get one, water was up to the wheels, but the water did not get inside the car I have daily drove the car without any issues since 18k miles, the car originally had 3.15's and now has 3.73's and new wheel bearings the following parts I bought brand... Read more
By Blkkbgt
I need some help here guys. As the title states I'm frustrated with the car right now. I've been in the garage for 3 hours with zero progress trying to get the fenders lined up. I'd really appreciate some input from either someone with autobody experience or someone who's completely pulled their front end apart, and put it all back together. I'm trying to get my fenders lined up starting at the door gap. For the life of me I cannot get the fender to sit high enough so the body lines that... Read more
By mtdubvee
Old thread I know but I’m looking at an SN-95 Roush Cobra. The dash plaque says stage 2, but it has a vortech. The Vortech could have been added, but I’ve also been told it was an option. Which I would assume would bump it to a stage 3. Has anyone ever seen a stage 3 Roush Cobra SN-95? Thanks For Sale 1997 Roush Mustang Cobra Stage 2 I am selling my 1997 Mustang Cobra Roush Stage 2 with 42,271 miles. Car is stock except for a custom tune and Pro Chamber mid pipe. I replaced the OEM springs, shocks and struts, with OEM parts. I bought the car 5 yrs ago with 38,694 miles. The car is in very goo…
By john11gt
I’ve been daily driving my 07 Duramax LBZ for almost 10 years and I love it. But, with diesel prices the way they are, I’m getting pretty tired of paying $160+ every week for fuel. So, I’ve been looking for a new daily with a budget around 15k with a max of 17k. I want something that is at least some fun to drive so it doesn’t make me want to sell it in a year or two. I’ve been considering manual 2017ish Subaru wrx’s and 2017ish Golf GTI’s. I’ve looked at a couple Subarus and put an... Read more
By Edgethis
Howdy everyone, i have this crank pulley and bracket that came off a Terminator. It looks to be in good shape. It doesnt fit my setup so I've never used it. Comes as pictured. Asking $300 plus shipping.
By Weather Man
I don't use a tool like this very often, but when you do need it, you need it.
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
