Every item links back to where it was published. Follow the sources you trust to build your own front page.
Threads shown here are headlines only. Reading and replying happens at the original forum, under its rules.
By Miloslavich
Toyota LandCruiser 100/105 Series Window Shades (J100/J105; 1998-2007) It's a perfect fit for Toyota LandCruiser 100/105 Series (J100/J105; 1998-2007) snapshades.com anybody run these in their 100 Series or LX470? I ordered a set today. Will post up how they are
By Antoine
Please let us know via the Poll and this thread, everyone's feedback would be greatly appreciated, thanks! * You can choose up to 3 reasons.
By GoneShawn
assembling a magnum block with trick flow heads and a custom hydraulic roller cam by Jones going in a 65 barracuda.. Sounds basic until I want to run a double roller timing set. and I dont think a tensioner makes any sense, Id rather get a quality timing chain, just like most ever other performance engine out there. So Now I hearing a double roller wont fit unless I use a double gasket? I have to cut the wings off the thrust plate. Could someone guide me throught the what it takes to get an... Read more
By Vette-kid
Where is the best place now for new rubber? I need the door main seals and the window seal. Prices are kinda all over for most pieces, but the window seals are pretty pricey for some reason. Over...
By myduster360
I picked up this Swinger(318/auto) roller a few months ago down in Southern Mo. It was exactly what I was looking for. New 1/4 panels, floors and paint & ready to be reassembled the way I wanted. Plus at just $2500 I couldn't pass it up The interior is bare but I have most all the pieces as well as a console. All of it is unfortunately Green. I'll be switching it all over to Black. So my initial choice for a drivetrain was a 5.7 Hemi and TKO. But more and more I started to lean... Read more
By Hotdogs
I am looking for measurements from a non ac car for the two mounting points on firewall that Classic Auto Air heater box bolts to the firewall. My car was an ac car so mounting locations for heater box were different. I know that the non ac car the fan hole was smaller on the firewall but I have that figured out. Thanks for any help. I have attached the photo from the instructions for reference.
By moro
I have spent quite a bit of time tinkering with my head unit attempting to figure out how to obtain a "DSP Flat", or at least the closest thing to it for those of us with the Premium Audio system. After re-reading through @SCOPESYS excellent write up, 2018 Premium Audio System , a few pieces started to fall into place. If you have not read his posts I highly recommend it. The external... Premium Audio System DSP Analysis and DSP Flat Solution
By jackport50
Excellent Condition, 20"Apex Forged VR-5RS Wheels w/ Hoosier Track Attack Pro tires: 981/718 Porsche Cayman (See Photos) Straight, no issues! No TPMS. Tire Size: Front 265/30ZR20 Rear...
By NC Engine Builder
So since I have a habit of posting long, drawn out engine builds, I figured yall might like a peak at the next race engine project. This one is a 440 small block, with W9 heads. Starting with this pile of used junk, we will see what I can do with it. The details are a well used R3, 9.200 deck, 48° block, a set of Brett Miller prepared W9 heads, a bryant billet crankshaft and a jesel belt cam drive setup. Will be "interesting"
By jackport50
Porsche 981/718 Cobra Black Vinyl Outer/Dinamica Circuit GRP Seats with BBI Seat Base and Slider Kit. ** Includes Lifeline harnesses - Expire 2028 Great condition. Two small rear seat patches...
By Rumblefish
Just got my oil changed at dealership. I checked oil after they change it and the tip of the dipstick is missing. Is the plastic tip prone to failure? If so what damage is it going to do to the engine if it remains inside? Can it be picked up by the pump or impede the pump from functioning properly? Will the crank shaft pull it into the engine and pulverize it into small pieces that will wreak havoc? They said they would replace the dipstick and drop the pan to look for it. Has anyone else... Read more
By SouthBay64
Both gas and temp gauges aren’t working. They light ups but that’s about it. I had the gauges check and they work. I was told the current wasn’t running through the circuits board because it was damaged. I swapped out the board and I still don’t have working gas or temp. The fuel sending unit is brand new. So I’m not sure what to swap out next.
By jackport50
Excellent Condition! Includes CMS Cutouts and fire extinguisher. Local pickup in RI
By YO-EL
Trying to see what the deal is with the decal as it folds over the nose of the hood. Some people have a cut out or a notch, others don't. Not sure if this is due to installation or possibly...
By Mburrrr
14’ Z51. So every time I open the driver or passenger door, lock or unlock with the fob, and even lock or unlock the car with the buttons on the door, it locks and unlocks the fuel door. It’s been...
By md-auto
Hello dear team i have cls63 c218 with an issue that drive me crazy, short history climate control switch was dead and we replaced with second hand one , now ac works but 1- tuning Ac on...
By rstoddard
I recently replaced the crankshaft seal and Timing Cover gasket (OEM cork gasket with FIPG) while renewing the HB, but I just noticed some oil leaking from the bottom of the Timing Cover where the two large bolts are. I snugged those bolts up as tight as I dared, as well as the smaller bolts. Is there anything else I can do? If I continue to see oil am I looking at replacing the gasket or is there any other options? Is putting RTV around the edge a waste of time and effort?
By red-bulli-69
Hi everyone, I’ve owned this beautiful F-150 for a week now, and I have a question: what is the correct name for the part marked above? Does anyone happen to have a part number, and what is the...
By toddsss
For 5% off any purchases at rockauto.com Just type: *352942778118008096* in the How Did You Hear About Us? box....
By SatelliteMan
Does anyone know if the original 4-speed starter shield is compatible with the Lakewood LK7000 bellhousing? It fills in above the front of the inspection cover, on the bottom of the bellhousing, up to the engine block. Attached are pics of the front of the bellhousing area and of the sheetmetal starter shield/cover. Before I try to track one down I was hoping someone had run into this question before, I couldn’t find the answer, searching around the interwebs.
By 924Carrera
Hi everyone, I have a pair of original Porsche 992 Spirit 70 seats and was wondering if anyone here has experience with these seats or with a similar OEM seat swap on a 992. I’m particularly...
By Ackcruisers
To help the Landcruiser community leverage openAI to help save time searching for tech info etc… I’m starting this thread to see how we can apply this new technology to Ih8mud. Post anything you feel is relevant but please do not post your personal views on artificial intelligence. Here is a link to ChatGBT Link How to use it? Ask a question like “what are the fluid capacities of the FJ40” then drop in the ih8mud link to a specific thread or general thread like 40 Series FAQ... Read more
By ALLEN007
We had our 50th high school reunion this past weekend (class of 76). The homecoming parade was last week as well. They asked us to be the Grand Marshal in the parade, then found out I had a 1976...
By LumpyCam
Back in May this year I asked on here about replacing the main battery and also whether it needed to be registered via a scanner. I installed a new battery and used my Launch scanner to reset the...
110 listed, 26 connected and bringing in items.
Know a publication, forum or channel we should list? Suggestions go to a review queue; nothing is connected until rights and identity are checked.
